Mitsubishi Montero (2002-2004). Manual — part 746
TSB Revision
SYMPTOM PROCEDURES
13Ad-33
STEP 10. Check harness connector B-01 or B-02 or B-03 at
right bank injector for damage.
(1) Check the injector connector, which deviated from the
standard value listed in Step 7.
Q: Is the harness connector in good condition?
YES : Repair harness wire between injector intermediate
connector and right bank injector connector because
of harness damage. Then confirm that the
malfunction symptom is eliminated.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
STEP 11. Check harness connector B-44 at the injector
intermediate connector for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
STEP 12. Check harness connector B-11, B-33, B-35 at the
left bank injector for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 13.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
AK200950
1
2
B-03(GR)
B-02(GR)
B-01(GR)
CONNECTORS: B-01, B-02, B-03
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK200949
3
4
7
8
1
2
5
6
B-44(B)
CONNECTOR: B-44
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK201292
1
2
B-11(GR)
B-35(GR)
B-33(GR)
CONNECTORS: B-11, B-33, B-35
AB
HARNESS
CONNECTORS:
COMPONENT SIDE
TSB Revision
SYMPTOM PROCEDURES
13Ad-34
STEP 13. Check the harness connector D-132 at the PCM
for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
TSB Revision
SYMPTOM PROCEDURES
13Ad-35
STEP 14. Check for harness damage between injector
connector and PCM connector.
a. Check the harness wire between injector connector B-
01 (terminal No. 2) and PCM connector D-132 (terminal
No. 1) when checking No. 1 cylinder injector.
b. Check the harness wire between injector connector B-
33 (terminal No. 2) and PCM connector D-132 (terminal
No. 5) when checking No. 2 cylinder injector.
c. Check the harness wire between injector connector B-
02 (terminal No. 2) and PCM connector D-132 (terminal
No. 14) when checking No. 3 cylinder injector.
d. Check the harness wire between injector connector B-
35 (terminal No. 2) and PCM connector D-132 (terminal
No. 21) when checking No. 4 cylinder injector.
e. Check the harness wire between injector connector B-
03 (terminal No. 2) and PCM connector D-132 (terminal
No. 2) when checking No. 5 cylinder injector.
f. Check the harness wire between injector connector B-
11 (terminal No. 2) and PCM connector D-132 (terminal
No. 6) when checking No. 6 cylinder injector.
Q: Is the harness wire in good condition?
YES : Check the following items, and repair or replace the
defective items.
a. Check the ignition coil, spark plugs, spark plug
cables.
b. Check if the injectors are clogged.
c. Check the compression pressure.
d. Check if the foreign materials (water,
kerosene, etc.) got into fuel.
e. Check the EGR valve.
Then confirm that the malfunction symptom is
eliminated.
NO : Repair it. Then confirm that the malfunction symptom
is eliminated.
INSPECTION PROCEDURE 8: Unstable Idle (Rough Idle, Hunting).
.
COMMENT
• In cases such as the above, the cause is proba-
bly the air/fuel mixture or electronic control throt-
tle valve system. Other systems affecting idle
quality include the ignition system and compres-
sion.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case: )
• Malfunction of the ignition system.
• Malfunction of air/fuel ratio control system.
• Malfunction of the electronic control throttle valve
system.
• Malfunction of the evaporative emission purge
solenoid system.
• Malfunction of the EGR valve.
• Poor compression pressure.
• Vacuum leak.
AK200960
1
2
B-03(GR)
B-11(GR)
B-35(GR)
B-33(GR)
B-02(GR)
B-01(GR)
CONNECTORS: B-01, B-02, B-03, B-11,
B-33, B-35
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK200938
2
3
4
5
6
7
8
9
1
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
11
12
13
AB
CONNECTOR: D-132
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-132(GR)
TSB Revision
SYMPTOM PROCEDURES
13Ad-36
DIAGNOSIS
Required Special Tool:
• MB991502: Scan Tool (MUT-II)
STEP 1. Check if the battery terminal is disconnected
Q: Has the battery terminal been disconnected lately?
YES : Start the engine and let it run at idle for approximate
10 minutes after engine warm up. Then, if a
malfunction occurs, go to Step 2.
NO : Go to Step 2.
STEP 2. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch is to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC set?
YES : Refer to GROUP 13A, Diagnostic Trouble Code Chart
NO : Go to Step 3.
STEP 3. Check the engine idling state.
Q: Is it hunting remarkably?
YES : Go to Step 4.
NO : Go to Step 5.
STEP 4. Check the following items.
(1) Carry out the following cleaning.
a. Refer to GROUP 13A, On-vehicle Service
− Clean the
throttle valve area
(2) After cleaning, confirm that the malfunction symptom is
eliminated.
Q: Is the malfunction symptom resolved?
YES : The check is completed.
NO : Check the following items, and repair or replace the
defective items.
a. Broken intake manifold gasket.
b. Broken air intake hose.
c. Broken vacuum hose.
d. Positive crankcase ventilation valve does not
operate.
Then confirm that the malfunction symptom is
eliminated.
ACX01539
16-PIN
MB991502
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст