Mitsubishi Montero (2002-2004). Manual — part 615
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-157
STEP 5. Using scan tool MB991502, check data list item 69:
Heated Oxygen Sensor Bank 1, Sensor 2 (right rear).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991502 to the data reading mode for item
69, Heated Oxygen Sensor Bank 1, Sensor 2 (right rear).
• Warming up the engine. When the engine is revved, the
output voltage should repeat 0 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
NO : Replace the PCM. Then go to Step 15.
ACX01539
16-PIN
MB991502
AC
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-158
STEP 6. Check harness connector C-14 at right bank
heated oxygen sensor (rear) and harness connector D-135
at PCM for damage.
Q: Is the harness connector in good condition?
YES : Check harness connector E-112 at intermediate
connector for damage, and repair or replace as
required. Refer to GROUP 00E, Harness Connector
Inspection
. If intermediate connector E-112 is
in good condition, repair harness wire between right
bank heated oxygen sensor (rear) connector C-14
(terminal No. 4) and PCM connector D-135 (terminal
No. 117) because of open circuit or harness damage.
Then go to Step 15.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 15.
AK201276
1
2
3
4
CONNECTOR: C-14
C-14(GR)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
RIGHT BANK
HEATED OXYGEN
SENSOR (REAR)
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-159
STEP 7. Check harness connector C-14 at right bank
heated oxygen sensor (rear) for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 15.
AK201276
1
2
3
4
CONNECTOR: C-14
C-14(GR)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
RIGHT BANK
HEATED OXYGEN
SENSOR (REAR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-160
STEP 8. Check the continuity at right bank heated oxygen
sensor (rear) harness side connector C-14.
(1) Disconnect the connector C-14 and measure at the harness
side.
(2) Check for the continuity between terminal No. 2 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 11.
NO : Go to Step 9.
STEP 9. Check harness connector D-135 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 15.
AK201276
1
2
3
4
CONNECTOR: C-14
C-14(GR)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
RIGHT BANK
HEATED OXYGEN
SENSOR (REAR)
AKX01497AF
1
2
4
3
C-14 HARNESS
CONNECTOR:
COMPONENT SIDE
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст