Mitsubishi Montero (2002-2004). Manual — part 577
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-5
STEP 3. Check connector B-48 at volume airflow sensor
and connector D-133 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AK200939
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
52
53
54
55
56
57
58
50
51
AB
CONNECTOR: D-133
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-133(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-6
STEP 4. Check for short circuit to ground between volume
airflow sensor connector B-48 (terminal No. 7) and PCM
connector D-133 (terminal No. 37).
Q: Is the harness wire in good condition?
YES : Replace the volume airflow sensor. Then go to Step
NO : Repair it. Then go to Step 9.
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AK200939
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
52
53
54
55
56
57
58
50
51
AB
CONNECTOR: D-133
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-133(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-7
STEP 5. Measure the reset signal voltage at volume airflow
sensor connector B-48 by backprobing.
(1) Do not disconnect the connector B-48.
(2) Start the engine and run at idle.
(3) Measure the voltage between terminal No. 7 and ground by
backprobing.
• When the engine idling, voltage should be 1.0 volt or
less.
• When the engine speed is 3,000 r/min, voltage should
be between 6.0 and 9.0 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. Check connector B-48 at volume airflow sensor
and connector D-133 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AKX01515
6 7
1 2 3 4 5
AKX01515
AJ
B-48 HARNESS
CONNECTOR:
HARNESS SIDE
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AK200939
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
52
53
54
55
56
57
58
50
51
AB
CONNECTOR: D-133
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-133(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-8
STEP 7. Check for open circuit and harness damage
between volume airflow sensor connector B-48 (terminal
No. 7) and PCM connector D-133 (terminal No. 37).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 9.
NO : Repair it. Then go to Step 9.
STEP 8. Replace the volume airflow sensor.
(1) Replace the volume airflow sensor.
(2) Carry out a test drive with the drive cycle pattern. Refer to
GROUP 13A, Procedure 6
− Other Monitor
(3) Check the diagnostic trouble code (DTC).
Q: Is DTC P0101 set?
YES : Replace the PCM. Then go to Step 9.
NO : The inspection is complete.
STEP 9. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
GROUP 13A, Procedure 6
− Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0101 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
AK200939
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
52
53
54
55
56
57
58
50
51
AB
CONNECTOR: D-133
HARNESS CONNECTOR:
COMPONENT SIDE
PCM
D-133(GR)
AK200937
3
4
5
1
2
6
7
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-48
B-48(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст