Mitsubishi Montero (2002-2004). Manual — part 624
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-193
STEP 3. Measure the sensor output voltage at PCM
connector D-135 by backprobing.
(1) Do not disconnect the connector D-135.
(2) Start the engine and run at idle.
(3) Measure the voltage between terminal No. 108 and ground
by backprobing.
• Warming up the engine. When the engine is 2,500 r/min,
the output voltage should repeat 0 to 0.8 volt alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 4.
NO : Go to Step 6.
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
AK201410
9192
939495
96979899
100
105
113114
115116117
118119120
106
107108109
110111112
101102103
104
D-135 HARNESS
CONNECTOR:
HARNESS SIDE
AB
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-194
STEP 4. Check harness connector B-26 at left bank heated
oxygen sensor (front) and harness connector D-135 at
PCM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 15.
AK201278
1
2
3
4
CONNECTOR: B-26
B-26(GR)
AB
HARNESS
CONNECTOR:
COMPONENT
SIDE
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-195
STEP 5. Using scan tool MB991502, check data list item 11:
Heated Oxygen Sensor Bank 2, Sensor 1 (left front).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991502 to the data reading mode for item
11, Heated Oxygen Sensor Bank 2, Sensor 1 (left front).
• Warming up the engine. When the engine is revved, the
output voltage should be 0.6 to 1.0 volt.
• Warming up the engine. When the engine is idling, the
output voltage should repeat 0.4 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
NO : Replace the PCM. Then go to Step 15.
ACX01539
16-PIN
MB991502
AC
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-196
STEP 6. Check harness connector B-26 at left bank heated
oxygen sensor (front) and harness connector D-135 at
PCM for damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between left bank heated oxygen
sensor (front) connector B-26 (terminal No. 4) and
PCM connector D-135 (terminal No. 108) because of
open circuit or harness damage. Then go to Step 15.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 15.
AK201278
1
2
3
4
CONNECTOR: B-26
B-26(GR)
AB
HARNESS
CONNECTOR:
COMPONENT
SIDE
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст