Mitsubishi Montero (2002-2004). Manual — part 570
DATA LIST REFERENCE TABLE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
13Ab-37
INJECTOR
BNK1
47
Injectors bank
1 (right)*
2
Engine:
cranking
When engine
coolant
temperature is
0
°C (32 °F)
100
− 160 mS -
-
When engine
coolant
temperature is
20
°C (68 °F)
37
− 67 mS
When engine
coolant
temperature is
80
°C (176 °F)
9.5
− 11.5 mS
Injectors bank
1 (right)*
3
• Engine
coolant
temperature
: 80
− 95°C
(176
−
203
°F)
• Lights,
electric
cooling fan
and all
accessories
: OFF
• Transmission:
"P" range
Engine is idling 2.2
− 3.4 mS
2,500 r/min
2.0
− 3.2 mS
When engine is
suddenly
revved
Increases
INJECTOR
BNK2
41
Injectors bank
2 (left)*
2
Engine:
cranking
When engine
coolant
temperature is
0
°C (32°F)
100
− 160 mS -
-
When engine
coolant
temperature is
20
°C (68°F)
37
− 67 mS
When engine
coolant
temperature is
80
°C (176°F)
9.5
− 11.5 mS
Injectors bank
2 (left)*
3
• Engine
coolant
temperature
: 80
− 95°C
(176
−
203
°F)
• Lights,
electric
cooling fan
and all
accessories
: OFF
• Transmission:
"P" range
Engine is idling 2.2
− 3.4mS
2,500 r/min
2.0
− 3.2mS
When engine is
suddenly
revved
Increases
MUT-II
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
DATA LIST REFERENCE TABLE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
13Ab-38
LONG
TRIM B1
81*
5
Long-term fuel
trim (trim) bank
1
Engine: warming up, 2,500 r/min
without any load (during closed
loop)
-12.5
− 12.5% Code No.
P0171, P0172
LONG
TRIM B2
83*
5
Long-term fuel
trim (trim) bank
2
Engine: warming up, 2,500 r/min
without any load (during closed
loop)
-12.5
− 12.5% Code No.
P0174, P0175
MDP
SENSOR
95
Manifold
differential
pressure
sensor
Engine: warming up, idling
20.6
− 34.0
kPa (6.1
−
10.0 in.Hg)
Code No.
P1400
PSP
SWITCH
27
Power steering
pressure
switch
Engine: idling
Steering wheel
stationary
OFF
Code No.
P0551
Steering wheel
turning
ON
SHORT
TRIM B1
82*
5
Short-term fuel
trim (trim) bank
1
Engine: warming up, 2,500 r/min
without any load (during closed
loop)
-12.5
− 12.5% Code No.
P0171, P0172
SHORT
TRIM B2
84*
5
Short-term fuel
trim (trim) bank
2
Engine: warming up, 2,500 r/min
without any load (during closed
loop)
-12.5
− 12.5% Code No.
P0174, P0175
SYS.
STATUS
B1
88*
5
Fuel control
system status
bank 1 (right)
Engine:
warming up
2,500 r/min
Closed loop
Code No.
P0134
When engine is
suddenly
revved
Open loop
−
drive
condition
SYS.
STATUS
B2
89*
5
Fuel control
system status
bank 2 (left)
Engine:
warming up
2,500 r/min
Closed loop
Code No.
P0154
When engine is
suddenly
revved
Open loop
−
drive
condition
TANK
PRS.
SNSR
73
Fuel tank
differential
pressure
sensor
• Ignition switch: "ON"
• Fuel cap removal
−3.3 − 3.3
kPa
(
−0.97 − 0.97
in.Hg)
-
-
MUT-II
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
DATA LIST REFERENCE TABLE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
13Ab-39
TP SNSR
(MAIN)
79
Throttle
position sensor
(main)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No.
2, No. 3 and
No. 4 with
the use of
the special
tool:
MB991348.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
200
− 800 mV Code No.
P0122, P0123
Fully open the
throttle valve
with your finger
3,800
− 4,900
mV
No load
450
− 1,000
mV
A/C switch: "OFF"
→ "ON"
Voltage rises
• A/C switch: "OFF"
• Shift lever: "N" → "D"
TP LEARN
MID
9A
Throttle
position sensor
(main)
mid opening
learning value
Ignition switch: ON
500
− 2,000
mV
Code No.
P0122, P0123
MUT-II
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
DATA LIST REFERENCE TABLE
TSB Revision
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
13Ab-40
TP SNSR
(SUB)
14
Throttle
position sensor
(sub)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No.
2, No. 3 and
No. 4 with
the use of
the special
tool:
MB991348.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
2,200
− 2,800
mV
Code No.
P0222, P0223
Fully open the
throttle valve
with your finger
3,800
− 4,900
mV
TP SNSR
(MAIN)
8A*
5
Throttle
position sensor
(main)*
4
• Remove the
intake air
hose at the
throttle body
• Disconnect
the throttle
position
sensor, and
then
connect
terminal
numbers
No. 1, No.
2, No. 3 and
No. 4 with
the use of
the special
MB991348
tool.
• Ignition
switch: ON
Fully close the
throttle valve
with your finger
0
− 10 %
Code No.
P0122, P0123
Fully open the
throttle valve
with your finger
80
− 100 %
No load
450
− 1,000
mV
A/C switch: "OFF"
→ "ON"
Voltage rises
• A/C switch: "OFF"
• Shift lever: "N" → "D"
VAF
RESET
SIG
34
Volume airflow
sensor reset
signal
Engine:
warming up
Engine is idling ON
-
-
2,500 r/min
OFF
MUT-II
SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION
ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
INSPECTION
PROCEDURE
NO.
REFERENCE
PAGE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст