Mitsubishi Montero (2002-2004). Manual — part 1066
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-9
REMOVAL SERVICE POINT
.
<<A>> REAR BRAKE CALIPER ASSEMBLY REMOVAL
Remove the rear brake caliper assembly and support it with
wire or something similar.
INSTALLATION SERVICE POINTS
.
>>A<< ADJUSTER ASSEMBLY INSTALLATION
Install the adjuster so that the shoe adjusting bolt for the left
hand wheel is attached towards the rear of the vehicle, and the
shoe adjusting bolt for the right hand wheel is towards the front
of the vehicle.
.
11. REAR HUB ASSEMBLY (REFER
TO GROUP 27, REAR HUB
ASSEMBLY
12. BACKING PLATE
13. SHOE HOLD-DOWN PIN
REMOVAL STEPS (Continued)
ACX00705
ACX00706AB
SHOE ADJUSTING
BOLT
PARKING BRAKE LINING AND DRUM
TSB Revision
PARKING BRAKES
36-10
>>B<< SHOE-TO-ANCHOR SPRING INSTALLATION
CAUTION
The front and rear shoe-to-anchor springs are not inter-
changeable, so the spring with the paint mark must be
installed at the rear side.
Install the shoe-to-anchor springs in the order shown in the
illustration.
INSPECTION
M1361002600185
PARKING BRAKE LINING AND BRAKE DRUM
CHECK
1. Measure the thickness of the brake lining at several places.
Standard value: 3.0 mm (0.12 inch)
Minimum Limit: 1.0 mm (0.04 inch)
2. If the thickness of the brake lining is below the limit, replace
the shoe and lining assemblies on both sides of the vehicle.
Never replace only one side.
3. Measure the inside diameter of the brake disc in two places
or more.
Standard value: 199.0 mm (7.8 inch)
Limit: 200.0 mm (7.9 inch)
4. If the inside diameter exceeds the limit, or if it is excessively
worn on one side, replace the brake disc.
ACX01980AB
PAINT
REAR
1
2
RIGHT SIDE WHEEL
ACX00707AB
PAINT
REAR
1
2
LEFT SIDE WHEEL
ACX00708AB
ACX00709AB
SPECIFICATIONS
TSB Revision
PARKING BRAKES
36-11
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1361003500211
SERVICE SPECIFICATIONS
M1361000300263
LUBRICANT
M1361000400237
SEALANT
M1361000500085
ITEM
SPECIFICATION
Parking brake lever
G-sensor bracket mounting bolt
4.9
± 1.0 N⋅m (44 ± 8 in-lb)
Parking brake lining and drum
Anchor to shoe spring attaching nut
142
± 14 N⋅m (105 ± 10 ft-lb)
Rear brake caliper assembly mounting bolt
100
± 10 N⋅m (74 ± 7 ft-lb)
ITEM
STANDARD VALUE LIMIT
Parking brake lever stroke
[Parking brake lever pull force: Approximately 200N (45lb)]
5
− 7 notches
−
Rear brake lining thickness mm (in)
3.0 (0.12)
Minimum 1.0 (0.04)
Brake drum inside diameter mm (in)
199.0 (7.8)
200.0 (7.9)
ITEM
SPECIFIED LUBRICANT
Adjuster
Brake grease SAE J310, NLGI No.1
Backing plate
Shoe and lining assembly
ITEM
SPECIFIED SEALANT
REMARK
Shoe hold-down pin
3M
ä ATD Part No. 8633 or
equivalent
Drying sealant
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст