Mitsubishi Montero (2002-2004). Manual — part 501
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-175
INSPECTION PROCEDURE 17: Distortion on FM Only.
DIAGNOSIS
STEP 1. Check that the distortion is present
when the radio is tuned to another station.
Q: Does the distortion persist when the radio is tuned
to another station?
YES :
Go to Step 2.
NO :
The signal from that station is too weak.
STEP 2. Relocate the reception area and check.
Q: When relocating the reception area does the
distortion increase or decrease?
YES :
The cause may be multipath or fading
noise. Multipath noise is the echo that
occurs when the broadcast signal is
reflected by a large obstruction and enters
the receiver with a slight time delay relative
to the direct signal (repetitious buzzing). A
fading or buzzing noise may occur when the
broadcast beam is disrupted by obstructing
objects and the signal strength fluctuates
within a narrow range.
NO :
Repair or replace the radio and CD player.
Check that a distortion is resolved.
INSPECTION PROCEDURE 18: Auto Select Function Inoperative, too Few Automatic Stations are
Selected.
DIAGNOSIS
STEP 1. Check the state of the antenna.
Q: Is the mast antenna assembled?
YES :
Go to Step 2.
NO :
Assemble the mast antenna. The auto-
select function should operate normally.
STEP 2. Check the number of radio stations.
Q: Are there sufficient numbers of radio stations
within the area?
YES :
Go to Step 3.
NO :
Go to Step 4.
STEP 3. Check the distance from the
transmission antenna.
Q: Is there a transmission antenna within a range of 2
miles?
YES :
Go to Step 5.
NO :
Go to Step 4.
STEP 4. The check if there are not that many
radio stations and when there is no transmission
antenna in the vicinity.
Execute automatic selection and check to see that
the strongest radio frequency is receivable within the
area.
Q: Is reception of the strongest radio frequency
possible within the area?
YES :
There is no action to be taken.
NO :
Go to Step 5.
STEP 5. Check to see if inspections are taking
place is an area exposed to special electric
fields.
Q: Are inspections taking place under special electric
field conditions? (underground garage, inside a
building, etc.)?
YES :
Go to Step 6.
NO :
Go to Step 7.
STEP 6. Relocate and check.
Automatically receive in a good reception area that is
not exposed to special electric fields.
Q: Is reception of the strongest radio frequency
possible within the area?
YES :
There is no action to be taken.
NO :
Go to Step 7.
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-176
STEP 7. Check the connection of the antenna
plug and radio and CD player.
Q: Is the antenna plug thoroughly connected to the
radio and CD player?
YES :
Repair or replace the radio and CD player.
The auto-select function should operate
normally.
NO :
Thoroughly connect the antenna plug and
the radio and CD player. The auto-select
function should operate normally.
INSPECTION PROCEDURE 19: Preset Stations are Erased.
.
CIRCUIT OPERATION
Power is continuously supplied to the radio and CD
player.
.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably a faulty radio and CD player
memory backup power supply system circuit.
.
TROUBLESHOOTING HINTS
• Damaged wiring harness or connector.
• Malfunction of the radio and CD player.
Memory Backup Power Supply Circuit
AC204170
CONNECTORS : D-06, D-28
DJ
D-06
D-28
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-177
DIAGNOSIS
Required Special Tool:
• MB991223: Harness set
STEP 1. Measure at radio and CD player connector D-06 in
order to check the power supply circuit to the radio and
CD player (through the battery).
(1) Disconnect radio and CD player connector D-06, and
measure at the wiring harness side.
(2) Measure the voltage between terminal number 11 and
ground by backprobing.
• The voltage should equal approximately 12 volts (bat-
tery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Either repair or replace the radio and CD player.
Check that a memory is retained.
NO : Go to Step 2.
STEP 2. Check radio and CD player connector D-06 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is radio and CD player connector D-06 in good
condition?
YES : Go to Step 3.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check that a memory is retained.
AC204170
CONNECTOR : D-06
CS
HARNESS SIDE
1
7
2
8
10
11
5
13
6
14
12
4
9
3
AC204738DS
HARNESS SIDE: D-06
6
14
4 5
13
11
3
9 10
2
8
1
7
12
AC204170
CONNECTOR : D-06
CS
HARNESS SIDE
1
7
2
8
10
11
5
13
6
14
12
4
9
3
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-178
STEP 3. Check the wiring harness between radio and CD
player connector D-06 (terminal 11) and the battery.
NOTE: Also check intermediate connector D-28. If intermediate
connectors D-28 is damaged, repair or replace the connector
as described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between radio and CD player
connector D-06 (terminal 11) and the battery in good
condition?
YES : Repair or replace the radio and CD player. Check that
a memory is retained.
NO : Repair the wiring harness. Check that a memory is
retained.
INSPECTION PROCEDURE 20: CD can not be Inserted.
DIAGNOSIS
STEP1. Check that a CD has been already loaded.
Q: Has a CD been already loaded?
YES :
Take out the CD (If the CD can not be
ejected, refer to INSPECTION
PROCEDURE 24
.) Check that a
CD can be inserted.
NO :
Go to Step 2.
STEP 2. Check how a CD is inserted.
Ensure that the ignition switch is at "ACC" or "ON".
NOTE: If you try to load a CD when the ignition
switch is at the positions other than "ACC" or "ON,"
the CD will not be inserted completely and then
rejected.
Q: If you try to load the CD, does the CD stops halfway
and then rejected?
YES :
Refer to INSPECTION PROCEDURE 24
NO :
Go to Step 3.
STEP 3. Check after the CD is loaded.
NOTE: Even though the CD is loaded, "E" (error) is
sometimes displayed with the CD rejected because
of vibration/shock or dew on the CD face or optical
lens.
Q: Though the CD is inserted completely, is "E" (error)
displayed and the CD ejected?
YES :
Go to Step 4.
NO :
There is no action to be taken.
STEP 4. Check the CD.
Check the CD for the conditions below:
• Is the CD loaded with its label facing down?
• Is the recorded face dirty or scratched?
• Is there dew on the recorded face?
Q: Is the CD in good condition?
YES :
Go to Step 5.
NO :
The original CD is defective. Check that a
CD can be inserted.
AC204188
CONNECTORS: D-06, D-28
D-28
D-06
BK
D-28
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
D-06
1
7
2
8
10
11
5
13
6
14
12
4
9
3
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст