Mitsubishi Montero (2002-2004). Manual — part 845
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-43
STEP 5. Measure the power supply voltage at PCM
connector D-132.
(1) Disconnect connector D-132 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Switch "ON" the auto-cruise control main switch.
(4) Measure the voltage between terminal 13 and ground.
• The voltage should measure battery positive voltage.
Q: Is the measured voltage battery positive voltage?
YES : Replace the PCM. Refer to
, Auto-cruise
Control.
NO : Go to Step 6.
AC205048
CONNECTOR: D-132
D-132(GR)
PCM
AB
1
2
5
6
8 7
14
15
16
21
22
23
9
17
24
10
18
25
12 11
19
26
13
3
4
20
27
AC205058AB
D-132 HARNESS
CONNECTOR:
COMPONENT SIDE
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-44
STEP 6. Check PCM connector D-132, intermediate
connector E-110 and combination meter connector D-04
for looser, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 7.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC205048
CONNECTOR: D-132
D-132(GR)
PCM
AB
AC205045
6
1
7
2
9
8
10
3
5
12
11
4
1314
E-110
CONNECTOR: E-110
AB
AC205052
CONNECTOR: D-04
AB
D-04 (GR)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-45
STEP 7. Check the harness for open circuit or short circuit
to ground between PCM connector D-132 terminal 13 and
combination meter connector D-04 terminal 45.
Q: Is the harness wire in good condition?
YES : Go to Step 8.
NO : Repair or replace the harness wire.
AC205048
CONNECTOR: D-132
D-132(GR)
PCM
AB
AC205052
CONNECTOR: D-04
AB
D-04 (GR)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-46
STEP 8. Check the combination meter.
(1) Remove the combination meter and measure at the
combination meter side. (Refer to GROUP 54A,
Combination Meter Assembly and Vehicle Speed Sensor
.)
(2) Measure the continuity between combination meter
connector D-03 terminal 62 and combination meter
connector D-04 terminal 45.
• The resistance should measure less than 2 ohms.
Q: Is the resistance less than 2 ohms?
YES : Replace the PCM. Refer to
, Auto-cruise
Control.
NO : Replace the combination meter. Refer to GROUP
54A, Combination Meter Assembly and Vehicle
Speed Sensor
DATA LIST REFERENCE TABLE
M1172002400244
CAUTION
• When shifting the selector lever to D range, the brakes should be applied so that the vehicle does
not move forward.
• Driving tests always need two persons: one driver and one observer.
NOTE: *:Disconnect the throttle position sensor connector, and then delete the diagnostic trouble code that
was recorded during the inspection with the use of the MB991502 scan tool after the inspection has been
completed.
31 32 33 34 35 36 37 38
39
40 41 42 43 44 45 46 47
5152 53 54 55 56 57 58
59
60 6162 63 64 65 66 67
ACX01926
D-04
COMBINATION METER
(REAR VIEW)
AC
CONNECTORS: D-03, D-04
D-03
MUT-II SCAN
TOOL
DISPLAY
ITEM
NO.
INSPECTION ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
APP SNS
(MAIN)
12
Accelerator pedal
position sensor (main)
Ignition
switch:
"ON"
Accelerator pedal: Released
905
− 1,165 mV
Accelerator pedal: Gradually
depressed
Increases in
response to the
pedal depression
stroke
Accelerator pedal: Fully
depressed
4,035 mV or more
BRAKE SW
06
Stoplight switch
Brake pedal: Depressed
ON
Brake pedal: Released
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст