Mitsubishi Montero (2002-2004). Manual — part 49
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-59
STEP 6. Check the wiring harness between rear A/C
control unit connector E-20 (terminal 3, 4 and 8) and rear
A/C switch connector E-22 (terminal 5, 3 and 13).
NOTE: Also check intermediate connector D-112. If intermedi-
ate connector D-112 is damaged, repair or replace the connec-
tor as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between rear A/C control unit
connector E-20 (terminal 3, 4 and 8) and rear A/C switch
connector E-22 (terminal 5, 3 and 13) in good condition?
YES : Go to Step 7.
NO : Repair the wiring harness. Check that the rear air
conditioning works normally.
AC204176
CONNECTOR : E-20
AY
HARNESS SIDE
7
8
3
10 9
2
4
11
1312
5
14
6
1
AC204175
CONNECTOR : E-22
AG
HARNESS SIDE
FLOOR
COSOLE
1
7
2
8
10
11
5
13
6
14
12
4
9
3
AC204171 AL
CONNECTOR : D-112
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-60
STEP 7. Check the air mixing damper control motor and
potentiometer
CAUTION
Do not apply battery voltage when the damper is in the
MAX HOT/MAX COOL position.
Check the air mixing damper control motor by the following pro-
cedures.
When checking the air mixing damper control motor, measure
the resistance value between the terminals 3 and 5, between
the terminals 3 and 7. At this time, make sure that the mea-
sured resistance value changes slowly within the standard
value.
Standard value: 1.2
− 4.8 kΩ
Q: Does air mixing damper control motor work normally?
YES : Go to Step 8.
NO : Replace the air mixing damper control motor. Check
that the rear air conditioning works normally.
LEVER POSITION BATTERY
CONNECTION
LEVER
OPERATION
At the MAX COOL
position
• Connect
terminal 1 to the
positive battery
terminal
• Connect
terminal 2 to the
negative battery
terminal
The lever moves
from the MAX
COOL position to
the MAX HOT
position
At the MAX HOT
position
• Connect
terminal 2 to the
positive battery
terminal
• Connect
terminal 1 to the
negative battery
terminal
The lever moves
from the MAX HOT
position to the MAX
COOL position
AC001049AB
MAX HOT POSITION
MAX
COOL
POSITION
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-61
STEP 8. Check rear A/C control unit connector E-20 and air
mixing damper control motor and potentiometer G-26-2 for
damage.
Q: Is rear heater control unit connector E-20 and air mixing
damper control motor and potentiometer G-26-2 in good
condition?
YES : Go to Step 9.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
that the rear air conditioning works normally.
AC204176
CONNECTOR : E-20
AY
HARNESS SIDE
7
8
3
10 9
2
4
11
1312
5
14
6
1
AC204698
CONNECTOR : G-26-2
AK
HARNESS SIDE
7 6 5 4 3 2 1
REAR AIR CONDITIONING DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-62
STEP 9. Check the wiring harness between rear A/C
control unit connector E-20 (terminal 14, 6, 4, 7 and 8) and
air mixing damper control motor and potentiometer G-26-2
(terminal 2, 1, 5, 3 and 7).
AC204176
CONNECTOR : E-20
AY
HARNESS SIDE
7
8
3
10 9
2
4
11
1312
5
14
6
1
AC204699
CONNECTORS : G-26-1, G-26-2
AG
G-26-1
G-26-2
G-26-1
G-26-2
HARNESS SIDE
8
4
7
3
5
1
6
2
1
4
3
6 5
2
<VEHICLES WITH REAR AIR
CONDITIONING SYSTEM>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст