Mitsubishi Montero (2002-2004). Manual — part 472
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-59
STEP 6. Check the wiring harness between combination
meter connector D-03 (terminal 62) and ignition switch
(IG1).
NOTE: Also check junction block connectors D-208 and D-210.
If junction block connector D-208 or D-210 is damaged, repair
or replace the connector as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between combination meter
connector D-03 (terminal 62) and ignition switch (IG1) in
good condition?
YES : There is no action to be taken.
NO : Repair the wiring harness. Check to see that all
meters operate.
AC204170
CONNECTOR : D-03
AC
D-03(GR)
HARNESS
SIDE
51
52
61 60
53
54
56
57
55
63
66 65 64
59
62
58
67
D-03(GR)
AC204191
CONNECTORS: D-208, D-210
D-208
AC
HARNESS SIDE
HARNESS SIDE
D-210
D-208
D-210
1
2
3
5
6
4
1
2
7 6
3
9
4
11
12
10
13
5
8
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-60
STEP 7. Measure at combination meter connector D-32 in
order to check the ground circuit to the combination
meter.
(1) Disconnect combination meter connector D-32, and
measure at the wiring harness side.
(2) Measure the resistance between terminal 25 and ground.
• The resistance should equal 2 ohms or less.
(3) Measure the resistance between terminal 11 and ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Repair the combination meter. Check to see that all
meters operate.
NO : Go to Step 8.
STEP 8. Check combination meter connector D-32 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is combination meter connector D-32 in good
condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check to see that all meters operate.
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
AC204738 EP
HARNESS SIDE: D-32
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-61
STEP 9. Check the wiring harness between combination
meter connector D-32 (terminal 25 and 11) and ground.
Q: Is the wiring harness between combination meter
connector D-32 (terminal 25 and 11) and ground in good
condition?
YES : There is no action to be taken.
NO : Repair the wiring harness. Check to see that all
meters operate.
SPECIAL TOOLS
M1543000600950
ON-VEHICLE SERVICE
SPEEDOMETER CHECK
M1543000900296
Adjust the pressure of tires to the specified level. (Refer to
GROUP 31, On-vehicle Service
AC204170
CONNECTOR : D-32
CU
HARNESS SIDE
D-32(GR)
D-32(GR)
3
4
16
17
1
2
14
15
5
7 6
19
13
8
9
21
22
20
18
23
10
11
24
25
12
TOOL
TOOL NUMBER
AND NAME
REPLACED BY
MILLER TOOL
NUMBER
APPLICATION
MB991502 Scan tool
(MUT-II)
DRB-III (Scan tool)
Reading MFI system
diagnostic trouble code
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
General service tool
(jumper)
Making voltage and
resistance
measurements during
troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit
inspection
C: Power circuit
inspection
D: Commercial tester
connection
B991502
MB991223
A
B
C
D
AC
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-62
CAUTION
Place the transfer shift lever to "2H" position.
1. Set the vehicle onto a speedometer tester and use wheel
chocks to hold the front wheels.
2. To prevent the sideward shaking of the front wheel, attach
the puller on the towing hook and the tie down hook at front
side and connect its both ends to the anchor plate.
3. To prevent the jumping out of the vehicle, attach the chain
and the wire whose both ends are tightly fixed to the rear
towing hook.
CAUTION
Do not increase/decrease speed rapidly while testing.
4. Check if the speedometer indicator range is within the
standard values.
Standard value: <Vehicles for U.S.A.>
Standard value: <Vehicles for Canada.>
5. If not to the standard value, inspect for proper tire size. If not
correct, replace tires with original size tires and retest. If
correct, replace the speedometer. If still not to standard
value, replace vehicle speed sensor.
STANDARD INDICATION
km/h (mph)
ALLOWANCE RANGE
km/h (mph)
16 (10)
14
− 18 (8.5 − 11.5)
40 (25)
38
− 42 (23.5 − 26.5)
80 (50)
78
− 83 (48.5 − 51.5)
120 (75)
118
− 123 (73.5 − 76.5)
161 (100)
158
− 165 (98.5 − 102.5)
STANDARD INDICATION
km/h
ALLOWANCE RANGE
km/h
20
19
− 24
40
40
− 44
80
80
− 85
120
120.5
− 125.5
160
160.5
− 165.5
ACX01629AB
ACX00775 AB
FRONT
ANCHOR PLATE
PULLER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст