Mitsubishi Montero (2002-2004). Manual — part 951
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-287
DTC 24, 25: Rear Propeller Shaft Speed Sensor System
ACX02197AB
Rear Propeller Shaft Speed Sensor System Circuit
AC204751
CONNECTOR : C-07
AB
1 2 3
C-07 (GR)
AC204170
CONNECTOR : D-01
CD
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-288
.
CIRCUIT OPERATION
• The rear propeller shaft speed sensor generates
0
⇔ 5 volts pulse signal when the rear propeller
shaft rotates. The pulse signal frequency
increases with a rise in rear propeller shaft
speed.
• The ear propeller shaft speed sensor is con-
nected to the transfer-ECU (terminals 9 and 18)
via the rear propeller shaft speed sensor connec-
tor (terminals 1 and 2).
• The transfer-ECU detects the rear propeller shaft
speed by the signal input to terminal 9.
• The rear propeller shaft speed sensor generates
the pulse signal as the hole in the rear output
shaft pass the magnetic tip of the sensor.
.
DTC SET CONDITIONS
In the case that the input signal from the rear propel-
ler shaft speed sensor is unstable when the APP
sensor voltage is 1.5 volts and over, the DTC 24 is
set as the open circuit or the short circuit of the rear
propeller shaft speed sensor. In the case that the
input signal from the rear propeller shaft speed sen-
sor is unstable when the freewheel engage switch is
ON condition, the DTC 25 is set as the open circuit or
the short circuit of the rear propeller shaft speed sen-
sor.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of the rear propeller shaft speed sen-
sor circuit
• Malfunction of the rear output shaft
• Damaged harness, connector
• Malfunction of the transfer-ECU
AC204191
CONNECTORS : D-208, D-212
5 6
2
4
3
1
JUNCTION BLOCK
(FRONT VIEW)
3
10
9
4
11
8
7
1
5
2
6
D-208
D-208
D-212
D-212
AS
AC204194
CONNECTORS : E-11, E-109
E-109
E-109
E-11
E-11
AW
3
10
16
9
7 8
6
1
4
2
5
11
14
1213
15
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-289
DIAGNOSIS
Required Special Tool:
• MB991502: Scan Tool (MUT-II)
STEP 1. Using scan tool MB991502, check data list item 03:
Rear Propeller Shaft Speed Sensor.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Start the engine.
(3) Set scan tool MB991502 to data reading mode for item 03,
Rear Propeller Shaft Speed Sensor.
• When driving at constant speed of 30 km/h (19 mph),
the display should be "30 km/h (19 mph)."
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope with
Intermittent Malfunction
NO : Go to Step 2.
STEP 2. Measure the power supply voltage at rear
propeller shaft speed sensor connector C-07.
(1) Disconnect connector C-07 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 3 and ground.
• The voltage should measure battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 5.
NO : Go to Step 3.
ACX01539AD
MB991502
16-PIN
AC204751
CONNECTOR : C-07
AB
1 2 3
C-07 (GR)
AC204918 AQ
C-07 HARNESS CONNECTOR :
COMPONENT SIDE
1
2
3
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-290
STEP 3. Check joint connector D-01, junction block
connector D-212 and intermediate connector E-11 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204170
CONNECTOR : D-01
CD
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204173
CONNECTOR : D-212
AZ
3
10
9
4
11
8
7
1
5
2
6
JUNCTION BLOCK
(FRONT VIEW)
AC204176
CONNECTOR : E-11
AZ
3
10
16
9
7 8
6
1
4
2
5
11
14
1213
15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст