Mitsubishi Montero (2002-2004). Manual — part 805
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-89
STEP 2. Check the harness for short circuit to power
supply between the SRS-ECU and the passenger's air bag
module.
(1) Disconnect SRS-ECU connector E-08.
DANGER
To prevents the air bag from deploying unintention-
ally, disconnect the passenger’s air bag module con-
nector D-11 to short the squib circuit.
(2) Unclip passenger’s air bag module connector D-11.
(3) Disconnect the passenger's air bag module connector D-11.
(4) Turn the ignition switch to the "ON" position.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(5) Measure the voltage between terminals 9, 10 and body
ground.
Voltage should measure 0 volt.
Q: Is the measured voltage within the specified range?
YES : Eras the diagnostic trouble code memory, and check
the diagnostic trouble code. If DTC 64 sets, replace
the SRS-ECU. (Refer to
.) Then go to Step
NO : Go to Step 3.
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
AC204125
CONNECTOR: D-11
AC
D-11 (R)
GLOVE BOX
STRIKER
13 14 15 16 17 18 19 20
5 6 7 8 9 10 11 12
1 2
3 4
AC006257AI
E-08 HARNESS
CONNECTOR:
HARNESS SIDE
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-90
STEP 3. Check the harness wires for short circuit to power
supply between SRS-ECU connector E-08 (terminal No.9
and 10) and passenger's air bag module connector D-11
(terminal No.1 and 2).
Q: Are the harness wires between SRS-ECU connector E-
08 (terminal No.9 and 10) and passenger's air bag
module connector D-11 (terminal No.1 and 2) in good
condition?
YES : Go to Step 4.
NO : Repair the harness wires between SRS-ECU
connector E-08 and passenger's air bag module
connector D-11. Then go to Step 4.
STEP 4. Recheck the diagnostic trouble code.
Q: Is DTC 64 set?
YES : Return to Step 1.
NO : The procedure is complete. (If no malfunctions are not
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
ACX01478AH
CONNECTOR: E-08
E-08 (Y)
HARNESS
CONNECTOR:
HARNESS SIDE
AC204125
CONNECTOR: D-11
AD
D-11 (R)
GLOVE BOX
STRIKER
1 2
HARNESS
CONNECTOR:
HARNESS SIDE
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-91
DTC 65: Passenger’s (Front) Air Bag Module (Squib) System Fault for Ground Circuit (Short-Circuited
to Ground)
.
CIRCUIT OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the front impact sensors
and the front air bag analog G-sensor. If the
impact is over a predetermined level, the SRS-
ECU outputs an ignition signal. At this time, if the
front air bag safing G-sensor is on, the SRS air
bag will inflate.
• The ignition signal is input to the air bag module
via the clock spring to inflate the air bag.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the passenger's air
bag module (squib). However, if no DTC resets, the
SRS warning light will be switched off (DTC will be
retained).
.
TROUBLESHOOTING HINTS
• Damaged harness wires and connectors
• Short to the ground in the passenger's air bag
module (squib) harness
• Malfunction of the SRS-ECU
.
AC204435AB
Passenger's (Front) Air Bag Module (Squib) Circuit
NOTE
: CONNECTOR LOCK SWITCH
CONNECTOR
CONNECTED: ON
CONNECTOR
DISCONNECTED: OFF
AC204125
CONNECTOR: D-11
AC
D-11 (R)
GLOVE BOX
STRIKER
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-92
DIAGNOSIS
Required Special Tools:
• MB991502: Scan Tool (MUT-II)
• MB991865: Dummy resister
• MB991866: Resister harness
STEP1. Check the passenger's air bag module.
(1) Disconnect the negative battery terminal.
(2) Unclip passenger’s air bag module connector D-11.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Disconnect the passenger's air bag module connector D-11,
and insert special tool MB991866 into the harness
connector by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check the
diagnostic trouble code.
Q: Is DTC 65 set?
YES : Go to Step 2.
NO : Replace the passenger's air bag module. (Refer to
AC204125
CONNECTOR: D-11
AC
D-11 (R)
GLOVE BOX
STRIKER
AC006042 AV
MB991865 (DUMMY
RESISTOR: 3
Ω
)
MB991866
(RESISTOR HARNESS)
D-11 HARNESS
CONNECTOR
D-11 PASSENGER'S AIR BAG
MODULE CONNECTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст