Mitsubishi Montero (2002-2004). Manual — part 514
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-227
STEP 2. Check the RV meter and A/C-ECU circuit by
backprobing.
(1) Do not disconnect RV meter connector D-08.
(2) ignition switch "ACC" position.
(3) Measure the voltage (waveform) between terminal 9 and
ground using an oscilloscope by backprobing.
(4) Measure the voltage (waveform) between terminal 10 and
ground by backprobing.
(5) Measure the voltage (waveform) between terminal 19 and
ground by backprobing.
Q: Is the measured voltage Hi = 4 to 5 volts and Lo = 0 to 1
volt?
YES : Replace the RV meter display.
No : Go to Step 5.
AC204738
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
AC204738 DV
HARNESS SIDE: D-08
AC204738 DW
HARNESS SIDE: D-08
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
AC204738 DX
HARNESS SIDE: D-08
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-228
STEP 3. Check the harness wires between RV meter
connector D-08 (terminal 9 and 10 and 19) and A/C-ECU
connector D-23 (terminal 16 and 17 and 6).
Q: Are harness wires between RV meter connector D-08
(terminal 9 and 10 and 19) and A/C-ECU connector D-23
(terminal 16 and 17 and 6) in good condition?
YES : There is no action to be taken.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
.
STEP 4. Check the A/C-ECU.
CAUTION
To Prevent to damage to scan toll MB991502, always turn
the ignition switch to "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Read the A/C diagnostic trouble code.
Q: Is the A/C diagnostic trouble code set?
YES : Carry out troubleshooting of the A/C.
NO : There is no action to be taken.
AC204188
D-08(B)
1
3
4
2
12
1413
11
6
7
8
10 9
18
19
20
16
17
5
15
AC204188
CONNECTORS: D-08, D-23
BU
HARNESS SIDE
HARNESS SIDE
D-08(B)
D-23(B)
D-23(B)
1
3
4
2
12
1413
11
6
7
8
10 9
18
19
20
16
17
5
15
ACX01539
16-pin
MB991502
AI
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-229
STEP 5. Check the A/C-ECU by backprobing.
(1) Do not disconnect A/C-ECU connector D-23.
(2) ignition switch "ACC" position.
(3) Measure the voltage (waveform) between terminal 6 and
ground using an oscilloscope by backprobing.
(4) Measure the voltage (waveform) between terminal 16 and
ground by backprobing.
(5) Measure the voltage (waveform) between terminal 17 and
ground by backprobing.
Q: Is the measured voltage Hi = 4 to 5 volts and Lo = 0 to 1
volt?
YES : Go to Step 6.
NO : Replace the A/C-ECU.
STEP 6. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES : If no malfunctions are not found in all steps, an
intermittent malfunction is suspected. Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
− How to Cope with Intermittent
Malfunction
NO : Replace the RV meter.
AC204738 DY
HARNESS SIDE: D-23
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
AC204738 DZ
HARNESS SIDE: D-23
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
AC204738 EA
HARNESS SIDE: D-23
20
19
18
17
7
6
15
14
4
3
11 12 13
5
1
9 10
2
16
8
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-230
CHECK AT RV METER TERMINAL
M1543007600241
ACX02122 AB
D-07
D-08
TERMINAL
NO.
INPUT/
OUTPUT
SIGNAL
SYMBOL
TERMINAL
VOLTAGE
(V)
HARNESS
DISCREPANCY
FAILURE SYMPTOM DUE
TO HARNESS
DISCREPANCY
1
− 4
−
−
−
−
−
−
5
Input
ISOK (MUT-II
data signal)
Hi: Battery
positive
voltage
Lo: 0
− 1
Open
circuit
Short
circuit
Impossible to communicate
between power train control
module and the scan tool by
the scan tool
6
Input/
output
DATA (ETACS
SWS data signal)
Hi: Battery
positive
voltage
Lo: 0
− 1
Open
circuit
Short
circuit
•Switch operating sound
(buzzer) cannot be heard.
•Daytime/night display mode
interlocked with tail lamp is
not switched.
•Lamp (illuminated button) is
not lighted
7
− 8
−
−
−
−
−
−
9
Input/
output
M-DATA (A/C)
(M-BUS data
signal)
Hi: 4
− 5
Lo: 0
− 1
Open
circuit
Short
circuit
•Air-conditioner information
screen is not displayed.
•Ambient temperature is not
indicated.
10
Input/
output
M-CLOCK (A/C)
(M-BUS clock
signal)
Hi: 4
− 5
Lo: 0
− 1
Open
circuit
Short
circuit
•Air-conditioner information
screen is not displayed.
•Ambient temperature is not
indicated.
11
− 14
−
−
−
−
−
−
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст