Mitsubishi Montero (2002-2004). Manual — part 285
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-187
STEP 38. Check the harness wiring between power
window relay connector D-219 (terminal 4) and rear power
window sub-switch (RH) connector H-19 (terminal 4).
AC203850AB
CONNECTOR: D-219
JUNCTION BLOCK
(FRONT VIEW)
D-219
1
2
3
4
5
JUNCTION
BLOCK SIDE
D-219
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-188
NOTE: Also check junction block connector D-208 and inter-
mediate connectors D-111 and F-23. If junction block connector
D-208, intermediate connector D-111 or F-23 is damaged,
repair or replace the connector as described in GROUP 00E,
Harness Connector Inspection
.
Q: Is the harness wiring between power window relay
connector (terminal 4) and rear power window sub-
switch (RH) connector H-19 (terminal 4) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the rear power window sub-switch (RH) should now
work normally.
AC203850AD
CONNECTOR: D-208
JUNCTION BLOCK
(FRONT VIEW)
D-208
D-208
1
2
3 4 5 6
AC203860AC
D-111
CONNECTOR: D-111
D-111
AC204484
AE
F-23
F-23
CONNECTORS: F-12, F-23
F-12
F-12
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-189
STEP 39. Check at rear power window sub-switch (RH)
connector H-19 in order to check the ground circuit to the
rear power window sub-switch (RH).
(1) Disconnect rear power window sub-switch (RH) connector
H-19, and measure at the harness side.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 43.
NO : Go to Step 40.
STEP 40. Check power window main switch connector H-
05 and rear power window sub-switch (RH) connector H-19
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are power window main switch connector H-05 and rear
power window sub-switch (RH) connector H-19 in good
condition?
YES : Go to Step 41.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the rear power window sub-
switch (RH) should now work normally.
AC204323
1
2
3
4
5
6
AF
CONNECTOR H-19
(HARNESS SIDE)
AC203774
CONNECTOR: H-05
AE
DRIVER'S DOOR
H-05
H-05
AC000316 AD
H-19
CONNECTOR: H-19
REAR DOOR<RH>
H-19
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-190
STEP 41. Check the harness wiring between power
window main switch connector H-05 (terminal 2) and rear
power window sub-switch (RH) connector H-19 (terminal
5).
AC203774
CONNECTOR: H-05
AF
DRIVER'S DOOR
H-05
H-05
(HARNESS SIDE)
AC000316 AE
H-19
CONNECTOR: H-19
REAR DOOR<RH>
(HARNESS SIDE)
H-19
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст