Mitsubishi Montero (2002-2004). Manual — part 792
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-37
STEP 5. Check the driver's side seat belt pretensioner
circuit at the SRS-ECU connector E-07.
(1) Disconnect SRS-ECU connector E-07.
(2) Disconnect driver's seat belt pretensioner connector F-27.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(3) Check for continuity between E-07 harness connector
terminals 29 and 30.
It should be open circuit.
Q: Does continuity exist?
NO : Eras the diagnostic trouble code memory, and check
the diagnostic trouble code. If DTC 26 sets, replace
the SRS-ECU. (Refer to
YES : Go to Step 6.
STEP 6. Check the harness for short circuit between SRS-
ECU connector E-07 (terminal No.29 and 30) and driver’s
seat belt pre-tensioner connector F-27 (terminal No.1 and
2).
NOTE: After inspecting intermediate connector E-19, inspect
the wiring harness. If the intermediate connector E-19 is dam-
aged, repair or replace it. (Refer to GROUP 00E, Harness Con-
nector Inspection
.) Then go to Step 7.
ACX01478AI
CONNECTOR: E-07
E-07 (Y)
AC204126
AB
CONNECTOR: F-27
F-27 (R)
CENTER
PILLAR
AC006244
34 35 36 37 38 39 40 41 42
25 26 27 28 29 30 31 32 33
21 22
23 24
AJ
E-07 HARNESS
CONNECTOR:
HARNESS SIDE
AC204603AC
CONNECTOR: E-19
FLOOR
CONSOLE
E-19
2
1
4
3
E-19
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-38
Q: Are harness wires between SRS-ECU connector E-07
(terminal No.29 and 30) and driver’s seat belt pre-
tensioner connector F-27 (terminal No.1 and 2) in good
condition?
YES : Go to Step 7.
NO : Repair the harness wires between SRS-ECU
connector E-07 and driver’s side seat belt pre-
tensioner connector F-27. Then go to Step 7.
STEP 7. Recheck for diagnostic trouble code.
Q: Is DTC 26 set?
YES : Return to Step 1.
NO : The procedure is complete. (If no malfunctions are not
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
ACX01478AJ
CONNECTOR: E-07
E-07 (Y)
34 35 36 37 38 39 40 41 42
25 26 27 28 29 30 31 32 33
21 22
23 24
HARNESS SIDE
CONNECTOR
(REAR VIEW)
AC204126
AC
CONNECTOR: F-27
F-27 (R)
CENTER
PILLAR
1 2
HARNESS
CONNECTOR:
HARNESS SIDE
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-39
DTC 27: Driver’ Seat Belt Pre-Tensioner (Squib) System Fault 2 (Open in the Squib Circuit)
.
AC102677
Driver's Seat Belt Pre-Tensioner (Squib)
AB
ACX01478AI
CONNECTOR: E-07
E-07 (Y)
AC204603AB
CONNECTOR: E-19
FLOOR
CONSOLE
E-19
AC204126
AB
CONNECTOR: F-27
F-27 (R)
CENTER
PILLAR
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-40
CIRCUIT OPERATION
The SRS-ECU judges how severe a collision is by
detecting signals from the front impact sensors and
the front air bag analog G-sensor. If the impact is
over a predetermined level, the SRS-ECU outputs an
ignition signal. At this time, if the front air bag safing
G-sensor is on, the pre-tensioner will deploy.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the driver's seat belt
pre-tensioner (squib).
.
TROUBLESHOOTING HITS
• Improper connector contact
• Open circuit in the driver's seat belt pretensioner
(squib) circuit
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tools:
• MB991502: Scan Tool (MUT-ll)
• MB991865: Dummy resister
• MB991866: Resister harness
STEP 1. Check the driver's seat belt pre-tensioner.
(1) Disconnect the negative battery terminal.
(2) Disconnect the driver's seat belt pretensioner connector F-
27.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into the harness connector by
backprobing.
(5) Connect the negative battery terminal.
(6) Erase diagnostic trouble code memory, and then check the
diagnostic trouble code.
Q: Is DTC 27 set?
YES : Go to Step 2.
NO : Replace the driver's seat belt pre-tensioner. (Refer to
AC204126
AB
CONNECTOR: F-27
F-27 (R)
CENTER
PILLAR
AC006042 AY
MB991866
(RESISTOR HARNESS)
F-27 HARNESS
CONNECTOR
MB991865 (DUMMY
RESISTOR: 3
Ω
)
F-27 SEAT BELT
PRE-TENSIONER
CONNECTOR (DRIVER'S SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст