Mitsubishi Montero (2002-2004). Manual — part 788
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-21
DTC 22: Driver's Air Bag Module (Squib) System Fault 2 (Open in the Squib Circuit)
.
AC204430
Driver's Air Bag Module (Squib) Circuit
NOTE
: CONNECTOR LOCK SWITCH
CONNECTOR
CONNECTED: ON
CONNECTOR
DISCONNECTED: OFF
AB
AC204226AD
CLOCK SPRING
D-206 (Y)
CONNECTORS: D-206, D-229
D-229
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-22
CIRCUIT OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the front impact sensors
and the front air bag analog G-sensor. If the
impact is over a predetermined level, the SRS-
ECU outputs an ignition signal. At this time, if the
front air bag safing G-sensor is on, the SRS air
bag will inflate.
• The ignition signal is input to the air bag module
via the clock spring to inflate the air bag.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the driver's side air
bag module (squib). The most likely causes for
this code to be set are the followings:
• Open circuit in the driver's air bag module
(squib) or harness
• Open circuit in the clock spring
• Malfunction of connector contact
However, if no DTC resets, the SRS warning light will
be switched off (DTC will be retained).
.
TROUBLESHOOTING HINTS
• Open circuit in the clock spring
• Open circuit due to improper neutral position of
the clock spring
• Open circuit in the driver's air bag module (squib)
circuit
• Disengaged driver's air bag module (squib) con-
nector
• Improper connector contact
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tools:
• MB991502: Scan Tool (MUT-II)
• MB991865: Dummy resister
• MB991866: Resister harness
STEP 1. Check the driver's air bag module.
(1) Disconnect the negative battery terminal.
(2) By sliding the A section (in the figure) of air bag module
connector D-229 in the arrow direction, disconnect the
connector.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into clock spring side air bag
module connector D-229 by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check the
diagnostic trouble code.
Q: Is DTC 22 set?
YES : Go to Step 2.
NO : Replace the driver's air bag module. (Refer to
AC100441AE
D-229 AIR BAG MODULE
CONNECTOR
STEERING WHEEL
A
AC006030 AH
D-229 AIR BAG
MODULE
CONNECTOR
MB991865
(DUMMY RESISTOR : 3
Ω)
MB991866 (RESISTOR
HARNESS)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-23
STEP 2. Check the clock spring.
(1) Disconnect the negative battery terminal.
(2) Disconnect clock spring connector D-206.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into clock spring harness
connector D-206 (terminal No.3 and 4) by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check
diagnostic trouble code.
Q: Is DTC 22 set?
YES : Go to Step 3.
NO : Replace the clock spring. (Refer to
.) Then
go to Step 4.
AC006031
D-206 CLOCK SPRING
CONNECTOR
AJ
MB991865
(DUMMY RESISTOR : 3
Ω)
MB991866 (RESISTOR
HARNESS)
1 2
4
3
(REAR VIEW)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-24
STEP 3. Check the harness between the SRS-ECU
connector E-08 (terminal No.11 and 12) and the clock
spring connector (terminal No.3 and 4) for open circuit.
(1) Disconnect SRS-ECU connector E-08 and clock spring
connector D-206, and measure at the wiring harness side.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(2) Check for continuity between the following terminals.
Between connector E-08 terminal 11 and connector D-206
terminal 3
Between connector E-08 terminal 12 and connector D-206
terminal 4
It should be less than 2 ohms.
Q: Does continuity exist?
YES : Eras the diagnostic trouble code memory, and check
the diagnostic trouble code. If DTC 22 sets, replace
the SRS-ECU. (Refer to
.) Then go to Step
NO : Repair the harness wires between SRS-ECU
connector E-08 and clock spring connector D-206.
Then go to Step 4.
STEP 4. Recheck for diagnostic trouble code.
Q: Is DTC 22 set?
YES : Return to Step 1.
NO : The procedure is complete. (If no malfunctions are not
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
AC204226AB
CONNECTOR: D-206
CLOCK SPRING
D-206 (Y)
1 2
4
3
AC200924
13 14 15 16 17 18 19 20
5 6 7 8 9 10 11 12
1 2
3 4
D-206 HARNESS
CONNECTOR:
HARNESS SIDE
E-08 HARNESS
CONNECTOR:
HARNESS SIDE
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст