Mitsubishi Montero (2002-2004). Manual — part 360
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-487
STEP 4. Check the fusible link (2) line of the power supply
circuit to the theft-alarm horn relay. Test at theft-alarm horn
relay connector A-11X.
(1) Disconnect theft-alarm horn relay connector A-11X and
measure the voltage available at the relay box side of the
connector.
(2) Measure the voltage between terminal 3 and ground, and
also between terminal 5 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 7.
NO : Go to Step 5.
STEP 5. Check theft-alarm horn relay connector A-11X for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is theft-alarm horn relay connector A-11X in good
condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. All the vehicle horn (including the theft-alarm
horn) should sound when the theft-alarm system is
triggered.
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
1
2
3
4
5
ACX01571AC
CONNECTOR A-11X
(RELAY BOX SIDE)
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-488
STEP 6. Check the wiring harness between theft-alarm
horn relay connector A-11X (terminals 3 and 5) and fusible
link (2).
Q: Is the wiring harness between theft-alarm horn relay
connector A-11X (terminals 3 and 5) and fusible link (2)
in good condition?
YES : Replace the ETACS-ECU. All the vehicle horn
(including the theft-alarm horn) should sound when
the theft-alarm system is triggered.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. All the
vehicle horn (including the theft-alarm horn) should
sound when the theft-alarm system is triggered.
STEP 7. Check theft-alarm horn relay connector A-11X and
theft-alarm horn connector A-04 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are theft-alarm horn relay connector A-11X and theft-
alarm horn connector A-04 in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. All the vehicle horn (including the theft-alarm
horn) should sound when the theft-alarm system is
triggered.
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
AC204167
CONNECTOR : A-04
HARNESS
SIDE
A-04(B)
A-04(B)
AB
1
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-489
STEP 8. Check the wiring harness between theft-alarm
horn relay connector A-11X (terminal 4) and theft-alarm
horn connector A-04 (terminal 1).
Q: Is the wiring harness between horn relay connector A-
11X (terminal 4) and theft-alarm horn connector A-04
(terminal 1) in good condition?
YES : Go to Step 9.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. All the
vehicle horn (including the theft-alarm horn) should
sound when the theft-alarm system is triggered.
STEP 9. Check theft-alarm horn relay connector A-11X and
ETACS-ECU connector D-223 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are theft-alarm horn relay connector A-11X and ETACS-
ECU connector D-223 in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. All the vehicle horn (including the theft-alarm
horn) should sound when the theft-alarm system is
triggered.
AC204167
CONNECTOR : A-04
HARNESS
SIDE
A-04(B)
A-04(B)
AB
1
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
AC204174
CONNECTOR : D-223
AC
D-223(B)
D-223(B)
HARNESS SIDE
42
43
50
51
45
46
53
54
52
44
48
5655
47
49
41
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-490
STEP 10. Check the wiring harness between theft-alarm
horn relay connector A-11X (terminal 1) and ETACS-ECU
connector D-223 (terminal 49).
NOTE: Also check intermediate connector D-27 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connectors D-27 is damaged, repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between theft-alarm horn relay
connector A-11X (terminal 1) and ETACS-ECU
connector D-223 (terminal 49) in good condition?
YES : Go to Step 11.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. All the
vehicle horn (including the theft-alarm horn) should
sound when the theft-alarm system is triggered.
STEP 11. Check the fit of the theft-alarm horn.
NOTE: The theft-alarm horn is grounded to the vehicle body via
its mounting bolt.
Q: Is the theft-alarm horn installed correctly?
YES : Replace the ETACS-ECU. All the vehicle horn
(including the theft-alarm horn) should sound when
the theft-alarm system is triggered.
NO : Install the theft-alarm horn correctly. All the vehicle
horn (including the theft-alarm horn) should sound
when the theft-alarm system is triggered.
AC204183
CONNECTOR : A-11X
RELAY BOX SIDE
AE
2 1
5
4
3
A-11X
AC204174
CONNECTOR : D-223
AC
D-223(B)
D-223(B)
HARNESS SIDE
42
43
50
51
45
46
53
54
52
44
48
5655
47
49
41
AC204170
CONNECTOR : D-27
AH
10
4
8
7
3
9
5
1
6
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст