Mitsubishi Montero (2002-2004). Manual — part 341
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-411
NOTE: Also check junction block connector D-212, joint con-
nector A-16 and intermediate connector D-28 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If junction block connector D-212, joint connector A-
16 or intermediate connector D-28 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between front turn-signal light
(RH) connector A-35 (terminal 1) and ETACS-ECU
connector D-222 (terminal 14) in good condition?
YES : Replace the socket. Verify that the turn-signal lights
illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
STEP 14. Check the rear turn-signal light bulb (LH).
(1) Remove the rear turn-signal (LH) light bulb.
(2) Verify that the rear turn-signal light bulb (LH) is not
damaged or burned out.
Q: Is the rear turn-signal (LH) light bulb in good condition?
YES : Go to Step 15.
NO : Replace the rear turn-signal (LH) light bulb. Verify that
the turn-signal lights illuminate normally.
AC204167
CONNECTOR : A-16
AE
5 6
2 3 4
1
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC204173
CONNECTOR : D-212
AF
HARNESS SIDE
7 6 5
2 1
9 8
11 10
4 3
D-212
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-412
STEP 15. Check the ground circuit to the rear combination
light (LH). Test at rear combination light (LH) connector G-
02.
(1) Disconnect rear combination light (LH) connector G-02 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 4 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 18.
NO : Go to Step 16.
STEP 16. Check rear combination light (LH) connector G-
02 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is rear combination light (LH) connector G-02 in good
condition?
YES : Go to Step 17.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC100256
1
4
2
3
5
6
AB
CONNECTOR G-02
(HARNESS SIDE)
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-413
STEP 17. Check the wiring harness between rear
combination light (LH) connector G-02 (terminal 4) and
ground.
Q: Is the wiring harness between rear combination light
(LH) connector G-02 (terminal 4) and ground in good
condition?
YES : Replace the socket assembly. Verify that the turn-
signal lights illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
STEP 18. Check rear combination light (LH) connector G-
02 and ETACS-ECU connector D-222 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are rear combination light (LH) connector G-02 and
ETACS-ECU connector D-222 in good condition?
YES : Go to Step 19.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lights illuminate
normally.
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-414
STEP 19. Check the wiring harness between rear
combination light (LH) connector G-02 (terminal 5) and
ETACS-ECU connector D-222 (terminal 15).
NOTE: Also check junction block connector D-217 and inter-
mediate connector D-125 for loose, corroded, or damaged ter-
minals, or terminals pushed back in the connector. If junction
block connector D-217 or intermediate connector D-125 is
damaged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between rear combination light
(LH) connector G-02 (terminal 5) and ETACS-ECU
connector D-222 (terminal 15) in good condition?
YES : Replace the socket assembly. Verify that the turn-
signal lights illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lights illuminate normally.
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204179
CONNECTOR : G-02
AB
HARNESS SIDE
G-02(B)
G-02(B)
1
4
2
3
5
6
AC204170
CONNECTOR : D-125
AO
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204173
CONNECTOR : D-217
AG
HARNESS SIDE
8
1
11 10
3
4
12
9
2
13
14
6 5
15
7
D-217
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст