Mitsubishi Montero (2002-2004). Manual — part 465
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-31
REMOVAL SERVICE POINT
.
<<A>> STEERING LOCK CYLINDER REMOVAL
1. Insert the key in the steering lock cylinder and turn it to the
"ACC" position.
2. Using a small Phillips head screwdriver, pull the steering
lock cylinder toward you.
INSPECTION
M1543019501716
IGNITION SWITCH LESS CONINUITY CHECK
Disconnect ignition switch connector without removing the igni-
tion switch and steering lock cylinder. Then check the continu-
ity.
KEY REMINDER SWITCH CHECK
Disconnect key reminder switch connector without removing
the ignition switch and steering lock cylinder. Then check the
continuity.
IGNITION KEY RING ANTENNA CHECK
Check for continuity between terminal 3 and terminal 7.
Standard value: 2 ohms or less
ACX01628AB
LOCK PIN
SWITCH
POSITION
TESTER CONNECTION SPECIFIED
CONNECTION
"LOCK" (OFF) 1
− 2, 1 − 3, 1 − 4, 1 − 5,
1
− 6, 2 − 4, 2 − 5, 2 − 6,
4
− 5, 4 − 6
Open circuit
"ACC"
1
− 6
Less than 2 ohms
"ON"
1
− 2, 1 − 4, 1 − 6, 2 − 4,
2
− 6, 4 − 6
Less than 2 ohms
"START"
1
− 2, 1 − 4, 1 − 5, 2 − 4,
2
− 5, 4 − 5
Less than 2 ohms
ACX00769AB
STATUS OF
IGNITION KEY
TESTER
CONNECTION
SPECIFIED
CONNECTION
Removed
4
− 6
Less than 2 ohms
Inserted
4
− 6
Open circuit
ACX00770 AB
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-32
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED
SENSOR
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
DIAGNOSIS
INTRODUCTION TO COMBINATION METER DIAGNOSIS
M1543009900992
All vehicles are equipped with an electrical speedom-
eter, tachometer, fuel and coolant temperature
gauges. The individual gauges are not replaceable. If
the gauges do not function correctly, there is most
likely a fault in the electrical system. All inputs, pow-
ers and grounds must be confirmed as correct before
the combination meter can be condemned.
TROUBLESHOOTING STRATEGY
M1543006900528
Use these steps to plan your diagnostic strategy. Fol-
low through with each step to ensure that you have
exhausted all possible methods of finding a combina-
tion meter fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find and repair the malfunction by following the
symptom chart.
4. Verify that the malfunction has been eliminated.
SYMPTOM CHART
M1543007200771
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Speedometer does not work.
1
Tachometer does not work.
2
Fuel gauge does not work.
3
Engine coolant temperature gauge does not work.
4
Combination meter does not work.
5
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-33
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Speedometer does not Work.
Speedometer Circuit
AC204395
CONNECTOR : C-08
AJ
C-08(B)
AC204170
CONNECTOR : D-03
DC
D-03(GR)
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-34
.
CIRCUIT OPERATION
• The ignition switch (IG1) circuit is the power sup-
ply for the speedometer and vehicle speed sen-
sor.
• The vehicle speed sensor is installed on the
transmission. Four pulses are generated with one
turn of the vehicle speed sensor shaft. These
pulse signals are sent into the PCM and sent into
the speedometer. The speedometer calculates
the pulse signals, and operates the indicator. At
the same time, the travel distance is calculated.
.
TECHNICAL DESCRIPTION (COMMENT)
The cause may be a faulty vehicle speed sensor cir-
cuit system or a faulty speedometer. The vehicle
speed sensor is also used by the powertrain control
module (PCM), the auto-cruise control-ECU.
.
TROUBLESHOOTING HINTS
• Malfunction of the vehicle speed sensor
• Malfunction of the combination meter (printed-cir-
cuit board or speedometer and tachometer)
• Malfunction of the PCM
• Malfunction of the auto-cruise control-ECU
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
STEP 1. Check the speedometer by observing the other
meters.
Check to see that the tachometer, fuel gauge and water ther-
mometer are operating normally.
Q: Do all other meters operate?
YES <other meters all operate> : Go to Step 2.
NO <one of the meters do not operate> : Refer to
INSPECTION PROCEDURE 5
.
AC204171
CONNECTOR : D-116
AI
AC204176
CONNECTORS : E-111, E-114
E-111
AL
E-114
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст