Mitsubishi Montero (2002-2004). Manual — part 366
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-11
CIRCUIT OPERATION
The ETACS-ECU operates the fog lights according to
signal from the fog light switch.
.
TECHNICAL DESCRIPTION (COMMENT)
If the signal is not normal, the fog lights do not work
normally. If the signal is not normal, the fog light
switch or the ETACS-ECU may be defective.
.
TROUBLESHOOTING HINTS
• The fog light switch may be defective
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
STEP 1. Check the fog light switch.
Remove the fog light switch. Then check continuity between
the switch terminals.
Q: Is the fog light switch in good condition?
YES : Go to Step 2.
NO : Repair the fog light switch. If the for light switch
operates normally, it indicates that a correct signal is
sent from the fog light switch.
STEP 2. Check the ground circuit to the fog light switch.
Test at fog light switch connector D-127.
(1) Disconnect fog light switch connector D-127 and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 5.
NO : Go to Step 3.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released
1
− 2
Open circuit
Pressed
1
− 2
Less than 2 ohms
ACX00797
AC204170
CONNECTOR : D-127
HARNESS SIDE
AP
1
2
3
4
D-127
4 3 2 1
5
6
ACX01597AB
CONNECTOR D-127
(HARNESS SIDE)
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-12
STEP 3. Check fog light switch connector D-127 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is fog light switch connector D-127 in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Repair the fog light switch. If the for light
switch operates normally, it indicates that a correct
signal is sent from the fog light switch.
STEP 4. Check the wiring harness between fog light switch
connector D-127 (terminal 2) and ground.
NOTE: Also check joint connector D-30 for loose, corroded, or
damaged terminals, or terminals pushed back in the connector.
If joint connector D-30 is damaged, Repair or replace the dam-
aged component(s) as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between fog light switch
connector D-127 (terminal 2) and the ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the for light
switch operates normally, it indicates that a correct
signal is sent from the fog light switch.
AC204170
CONNECTOR : D-127
HARNESS SIDE
AP
1
2
3
4
D-127
AC204170
CONNECTOR : D-127
HARNESS SIDE
AP
1
2
3
4
D-127
AC204170
CONNECTOR : D-30
AJ
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-13
STEP 5. Check fog light switch connector D-127 and
ETACS-ECU connector D-224 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are fog light switch connector D-127 and ETACS-ECU
connector D-224 in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. If the for light switch operates normally, it
indicates that a correct signal is sent from the fog light
switch.
STEP 6. Check the wiring harness between fog light switch
connector D-127 (terminal 1) and ETACS-ECU connector D-
224 (terminal 24).
Q: Is the wiring harness between fog light switch
connector D-127 (terminal 1) and ETACS-ECU connector
D-224 (terminal 24) in good condition?
YES : Replace the ETACS-ECU. If the for light switch
operates normally, it indicates that a correct signal is
sent from the fog light switch.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the for light
switch operates normally, it indicates that a correct
signal is sent from the fog light switch.
AC204170
CONNECTOR : D-127
HARNESS SIDE
AP
1
2
3
4
D-127
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
AC204170
CONNECTOR : D-127
HARNESS SIDE
AP
1
2
3
4
D-127
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-14
INSPECTION PROCEDURE O-4: ETACS-ECU does not receive "R" position signal from the
transmission range switch.
Transmission Range Switch Input Circuit
AC204395
CONNECTOR : C-04
A-04(B)
AC
AC204170
CONNECTOR: D-01
AY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст