Mitsubishi Montero (2002-2004). Manual — part 352
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-455
STEP 6. Check dome light connectors F-03 and ETACS-
ECU connector D-222 for damage.
Q: Are dome light connector F-03 and ETACS-ECU
connector D-222 in good condition?
YES : Go to Step 7.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. Verify
that the dome light illuminates normally.
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204177
CONNECTOR : F-03
AC
HARNESS SIDE
1
2
F-03
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-456
STEP 7. Check the wiring harness between dome light
connector F-03 (terminal 2) and ETACS-ECU connector D-
222 (terminal 18).
NOTE: Also check intermediate connector D-26 and junction
block connector D-207 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If junction
block connector D-207 or intermediate connector D-26 is dam-
aged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between dome light connector F-
03 (terminal 2) and ETACS-ECU connector D-222
(terminal 18) in good condition?
YES : Replace the ETACS-ECU. Verify that the dome light
illuminates normally.
NO : Repair the wiring harness. Verify that the dome light
illuminates normally.
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC204177
CONNECTOR : F-03
AC
HARNESS SIDE
1
2
F-03
AC204170
CONNECTOR : D-26
AG
2 3
1
7
6
12
11
8
13
5
4
9 10
AC204173
CONNECTOR : D-207
AB
HARNESS SIDE
1
2
3
4
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-457
STEP 8. Check the dome light bulb.
Q: Is the dome light bulb in good condition?
YES : Go to Step 9.
NO : Replace the bulb. Verify that the dome light
illuminates normally.
STEP 9. Check the fusible link (1) line of the power supply
circuit to the dome light. Test at dome light connector F-03.
(1) Disconnect dome light connector F-03 and measure the
voltage available at the wiring harness side of the
connector.
(2) Measure the voltage between terminal 1 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Replace the dome light. Verify that the dome light
illuminates normally.
NO : Go to Step 10.
STEP 10. Check dome light connector F-03 for damage.
Q: Is dome light connector F-03 in good condition?
YES : Go to Step 11.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. Verify
that the dome light illuminates normally.
AC204177
CONNECTOR : F-03
AC
HARNESS SIDE
1
2
F-03
2
1
ACX01591AB
CONNECTOR F-03
(HARNESS SIDE)
AC204177
CONNECTOR : F-03
AC
HARNESS SIDE
1
2
F-03
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-458
STEP 11. Check the wiring harness between dome light
connector F-03 (terminal 1) and fusible link (1).
ACX02274
FUSIBLE LINK (1)
AE
BATTERY
AC204177
CONNECTOR : F-03
AC
HARNESS SIDE
1
2
F-03
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст