Mitsubishi Montero (2002-2004). Manual — part 1135
M-ASTC DIAGNOSIS
TSB Revision
MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM
35C-157
CAUTION
Always use the test harness when measuring the voltage
or resistance value at the female connector. If you fail to do
so, connectors may be damaged.
(4) Measure the resistance between intermediate connector E-
122 terminals 9 and 20.
• The resistance should measure 120 ± 12 ohms.
Q: Does the resistance measure 120
± 12 ohms?
YES : Go to Step 32.
NO : Replace the control wiring harness assembly.
AC204581
FEMALE CONNECTOR: E-122
TEST
HARNESS
AD
TEST
HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
M-ASTC DIAGNOSIS
TSB Revision
MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM
35C-158
STEP 32. Check power control module connector D-134, G
and yaw rate sensor connector E-126 and intermediate
connector E-123.
CAUTION
If there is a problem in the connector(s) (including termi-
nals) or wire(s) of the instrument panel wiring harness
assembly (the wiring harness connected to the steering
wheel sensor, the data link connector and the resistor) and
the transmission wiring harness assembly (the wiring har-
ness connected to the G and yaw rate sensor connector
and intermediate connector E-123), cut and repair the
defective wire so that the frayed end of the twisted wire
should be within 10 cm (4.0 inches). If it exceeds 10 cm (4.0
inches), twist the wiring harness just like the original
twisted wire. If the frayed end exceeds 10 cm (4.0 inches),
a communication error may be caused.
CAUTION
If there is a problem in the CAN bus line or the connectors
on the control wiring harness assembly (the wiring har-
AC204171
CONNECTOR: D-134
HARNESS SIDE
D-134(GR)
D-134(GR)
AE
80
87
73
66
67
65
74
81
75
82
6261
72
68
69
70
71
78
85
77
8483
76
79
86
63
64
8988
AC204176
CONNECTOR: E-123
AR
E-123(GR)
2
6
14
7
9 8
10
4
12
3
11
19
16
1817
15
1
5
13
E-123(GR)
AC204175
CONNECTOR: E-126
HARNESS SIDE
E-126(GR)
E-126(GR)
AB
FLOOR
CONSOLE
1
2
4 3
AC203824
CONNECTOR
TWISTED WIRE
AB
10 cm
(4.0 inches)
M-ASTC DIAGNOSIS
TSB Revision
MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM
35C-159
ness connected to the M-ASTC-ECU, the power control
module and intermediate connector E-123), do not attempt
to repair the wiring harness or connector(s), but replace
the wiring harness assembly. If a wire is added or the con-
nector(s) are repaired, an error in the CAN communication
may be caused.
Q: Are power control module connector D-134, G and yaw
rate sensor connector E-126 and intermediate
connector E-123 in good condition?
YES : Go to Step 33.
NO :
• If there is a problem at the transmission wiring
harness assembly side, repair or replace the
connector.
• If there is a problem at the control wiring harness
assembly side, replace the control wiring harness
assembly.
M-ASTC DIAGNOSIS
TSB Revision
MITSUBISHI ACTIVE SKID AND TRACTION CONTROL SYSTEM
35C-160
STEP 33. Check the CAN bus line for short circuit. Check
at intermediate connector E-123.
CAUTION
Before checking CAN bus lines and their interconnected
components, "ground" yourself, by touching a metal
object such as an unpainted pipe, this will discharge any
potentially damaging static that may have built up.
CAUTION
When measuring resistance value or voltage in CAN bus
lines, use a digital multimeter. If not using a digital multim-
eter, the equipments, which are connected through the
CAN communication lines, may be damaged.
(1) Disconnect intermediate connectors E-123, and G and yaw
rate sensor connector E-126, and measure the resistance
at the female intermediate connector (at the instrument
panel wiring harness side).
(2) Turn the ignition switch to the LOCK (OFF) position.
CAUTION
Disconnect the negative battery terminal when measuring
the resistance value in the CAN bus line. If you fail to do
so, the equipments, which are connected through the CAN
communication lines, may be damaged.
(3) Disconnect the negative battery terminal.
CAUTION
Always use the test harness when measuring the voltage
or resistance value at the female connector. If you fail to do
so, connectors may be damaged.
(4) Measure the resistance between intermediate connector E-
123 terminals 2 and 6.
• The resistance should be infinite.
Q: Is the resistance infinite?
YES <the resistance is infinite> : Go to Step 34.
NO <the resistance is not infinite> : Repair the wiring
harness wires between intermediate connector E-123
and the G and yaw rate sensor connector.
AC204176
CONNECTOR: E-123
AR
E-123(GR)
2
6
14
7
9 8
10
4
12
3
11
19
16
1817
15
1
5
13
E-123(GR)
AC204175
CONNECTOR: E-126
HARNESS SIDE
E-126(GR)
E-126(GR)
AB
FLOOR
CONSOLE
1
2
4 3
AC204581
FEMALE CONNECTOR: E-122
TEST
HARNESS
AD
TEST
HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст