Mitsubishi Montero (2002-2004). Manual — part 836

AUTO-CRUISE CONTROL

TSB Revision

ENGINE AND EMISSION CONTROL

17-7

AUTO-CRUISE CONTROL

GENERAL DESCRIPTION

M1172000100225

By using the auto-cruise control, the driver can select
and maintain a desired cruising speed [approxi-
mately 40 km/h (25 mph) or more] without depress-
ing the accelerator pedal.

CONSTRUCTION DIAGRAM

AC204216

3

11

1 2

9 10

14

6

5

4

1213

8

7

16

15

AC204217

AC204447

20

20

40

60

80

100 120

140

160

180

200

40

60

80

100

120

km/h

AC204919

AUTO-CRUISE
CONTROL
INDICATOR
LIGHT

ACCELERATOR
PEDAL
POSITION
SENSOR

TRANSMISSION
RANGE SWITCH

STOPLIGHT
SWITCH

THROTTLE BODY
ASSEMBLY

POWERTRAIN
CONTROL
MODULE (PCM)

AB

VEHICLE
SPEED
SENSOR

AUTO-CRUISE
CONTROL SWITCH

MAIN SWITCH

DATA LINK
CONNECTOR

AUTO-CRUISE CONTROL

TSB Revision

ENGINE AND EMISSION CONTROL

17-8

SPECIAL TOOLS

M1172000600220

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

INTRODUCTION TO AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

M1172003300217

The auto-cruise control system allows driving without
stepping on the accelerator pedal by setting a ran-
dom speed between 40 km/h (25 mph) and 200 km/h
(124 mph). Problems in this system can be investi-
gated by the following methods.

Auto-cruise control system diagnostic
trouble codes

The auto-cruise control system consists of the
powertrain control module (PCM), control switches
and sensors. The control switches and sensors mon-
itor the state of the vehicle. The PCM controls the
throttle valve opening angle in the throttle body in

accordance with the input signals from the switches
and sensors. If the PCM detects a problem on any of
those components, the PCM estimates where the
problem may be occurring, and will output a diagnos-
tic trouble code. Diagnostic trouble codes cover the
auto-cruise control switch, stoplight switch and PCM.

AUTO-CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY

M1172002000224

Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will check most of the

possible causes of an auto-cruise control system
problem.

TOOL

TOOL NUMBER AND
NAME

SUPERSESSION

APPLICATION

MB991502 Scan tool
(MUT-II)

MB991496-OD

Reading diagnostic
trouble codes

MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Inspection harness
B: LED harness
C: LED harness adapter
D: Probe

General service tools

Checking the continuity
and measuring the
voltage at the harness
connector

MB991348
Test harness set

MB991348-01

Checking throttle position
sensor

B991502

MB991223

A

D

C

B

AD

MB991348

AUTO-CRUISE CONTROL

TSB Revision

ENGINE AND EMISSION CONTROL

17-9

1. Gather information from the customer.
2. Verify that the condition described by the

customer exists.

3. Check the vehicle for any auto-cruise control

system DTC.

4. If you can verify the condition but no auto-cruise

control system DTCs are set, and the malfunction
may be intermittent. Refer to GROUP 00, How to
Use Troubleshooting/Inspection Service Points

−

How to Cope with Intermittent Malfunctions

P.00-

6

.

5. If you can verify the condition but there are no

auto-cruise control system DTCs, or the system
cannot communicate with scan tool MB991502,
refer to Symptom Chart

P.17-35

and find the fault.

6. If there is an auto-cruise control system DTC,

record the number of the code, then erase the
code from vehicle memory using the scan tool.

7. Re-create the auto-cruise control system DTC set

conditions to see if the same Auto-cruise Control
System DTC will set again.

• If the same Auto-cruise Control System DTC sets

again, perform the diagnostic procedures for the
set code. Refer to

P.17-12

, Auto-cruise Control

System Diagnostic Trouble Code Chart.

AUTO-CRUISE CONTROL SYSTEM DIAGNOSTIC
TROUBLE CODE DIAGNOSIS

M1172002100210

Retrieving Auto-cruise Control System
Diagnostic Trouble Codes.

.

Using scan tool MB991502

Required Special Tool:

• MB991502: Scan Tool (MUT-II)

CAUTION

To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
1. Connect scan tool MB991502 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Depress the auto-cruise control main switch to illuminate the

auto-cruise control indicator light in the combination meter.

4. Use scan tool MB991502 to check for auto-cruise control

system diagnostic trouble codes.

5. Turn the ignition switch to the "LOCK" (OFF) position.
6. Disconnect scan tool MB991502.

.

Using a Auto-cruise Control Indicator Light
1. Turn the ignition switch to the "ON" position while holding

the auto-cruise control switch in the "SET" position (down).
Then, within one second, more the cruise control switch up
to the "RES" position.

2. Read a diagnostic trouble code by observing the flash

display pattern of the auto-cruise control indicator light in the
combination meter.

ACX02258AC

MB991502

16-PIN

ACX01172

AB

AUTO-CRUISE
CONTROL
SWITCH

SET
SWITCH: ON

RESUME
SWITCH: ON

AUTO-CRUISE CONTROL

TSB Revision

ENGINE AND EMISSION CONTROL

17-10

DIAGNOSTIC RESULT DISPLAY METHOD WHEN USING THE AUTO-CRUISE
CONTROL INDICATOR LIGHT

NOTE: Other on-board diagnostic items are also out-
put as voltage waveforms corresponding to diagnos-
tic trouble code numbers.

Erasing Diagnostic Trouble Codes

The diagnostic trouble codes can be erased by the following
procedure.
NOTE: The diagnostic trouble code will not be erased even if
the negative battery terminal is disconnected.

.

Using scan tool MB991502

Required Special Tool:

• MB991502: Scan Tool (MUT-II)

CAUTION

To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
1. Connect scan tool MB991502 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Use scan tool MB991502 to check for auto-cruise control

system diagnostic trouble codes.

4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991502.

.

WHEN THE DIAGNOSTIC TROUBLE CODE NO.23 IS SET WHEN NO DIAGNOSTIC TROUBLE CODE

IS SET

AC204251AB

ILLUMINATED

NOT ILLUMINATED

PAUSE
TIME: 3s

1.5s 0.5s

TENS
SIGNAL

PLACE
DIVISION:
2s

UNITS
SIGNAL

0.5s

AC204252

CONTINUOUS ON AND OFF

SIGNALS AT INTERVALS OF 0.5 s

AB

0.5 s

ILLUMINATED

NOT ILLUMINATED

ACX02258AC

MB991502

16-PIN