Mitsubishi Montero (2002-2004). Manual — part 306
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-271
STEP 2. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
• Ignition switch: ACC
• Rear wiper switch: INT
Operate scan tool MB991502 according to the procedure below
to display "REAR WIPER."
1. Select "SWS."
2. Select "SYSTEM SELECT."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "REAR WIPER."
Check that normal conditions are displayed on the items
described in the table below.
Q: Are normal conditions displayed for "REAR WIPER SW"
and "IG SW (ACC)"?
YES : Go to Step 3.
NO :
• Normal condition is not displayed on the "REAR
WIPER SW": Refer to Inspection Procedure O-7
"ETACS-ECU does not receive a signal from the
rear wiper switch
• Normal condition is not displayed on the "IG SW
(ACC)": Refer to Inspection Procedure O-1
"ETACS-ECU does not receive a signal from the
ignition switch (ACC)
."
ITEM NO.
ITEM NAME
NORMAL
CONDITION
ITEM 13
REAR WIPER SW ON
ITEM 31
IG SW (ACC)
ON
AC204222AB
16-pin
13-pin
MB991502
MB991862
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-272
STEP 3. Check the battery power supply circuit to the rear
wiper motor. Test at rear wiper motor connector I-07.
(1) Disconnect rear wiper motor connector I-07 and measure
the voltage available at the harness side of the connector.
(2) Turn the rear wiper switch to the "ON" position.
(3) Measure the voltage between terminal 2 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 7.
NO : Go to Step 4.
STEP 4. Check the rear wiper motor connector I-07 and
ETACS-ECU connector D-222 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are rear wiper motor connector I-07 and ETACS-ECU
connector D-222 in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the rear wiper works normally.
ACX02293
CONNECTOR: I-07
AQ
I-07(B)
I-07(B)
1 2 3 4
AC204312 AE
CONNECTOR I-07
(HARNESS SIDE)
4 3 2 1
ACX02293
CONNECTOR: I-07
AR
I-07(B)
I-07(B)
(HARNESS SIDE)
1
2
3
4
AC203853
CONNECTOR: D-222
AC
JUNCTION BLOCK (REAR VIEW)
D-222
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-273
STEP 5. Check the harness wires between rear wiper
motor connector I-07 (terminal 2) and ETACS-ECU
connector D-222 (terminal 1).
ACX02293
CONNECTOR: I-07
AR
I-07(B)
I-07(B)
(HARNESS SIDE)
1
2
3
4
AC203853
CONNECTOR: D-222
AC
JUNCTION BLOCK (REAR VIEW)
D-222
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-274
NOTE: Also check intermediate connectors G-10, D-111 and
junction block connector D-217. If intermediate connectors G-
10, D-111 or junction block connector D-217 are damaged,
repair or replace damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between rear wiper motor
connector I-07 (terminal 2) and ETACS-ECU connector
D-222 (terminal 1) in good condition?
YES : Go to step 6.
NO : The wiring harness may be damaged or the
connectors may have loose, corroded or damaged
terminals or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the rear wiper works normally.
AC204524
CONNECTOR: G-10
AC
G-10
G-10
AC203860AC
D-111
CONNECTOR: D-111
D-111
AC203850
CONNECTOR: D-217
AH
D-217
JUNCTION BLOCK
(FRONT VIEW)
D-217
1
8 9 10 11
13 14 15
12
2 3 4
5 6 7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст