Mitsubishi Montero (2002-2004). Manual — part 399
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-143
STEP 5. Check hood switch connector A-14 and ETACS-
ECU connector D-223 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are hood switch connector A-14 and ETACS-ECU
connector D-223 in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. If the theft-alarm system operates normally,
it indicates that a correct signal is sent from the hood
switch.
AC204167
CONNECTOR : A-14
HARNESS
SIDE
A-14(B)
A-14(B)
AC
1
2
AC204174
CONNECTOR : D-223
AC
D-223(B)
D-223(B)
HARNESS SIDE
42
43
50
51
45
46
53
54
52
44
48
5655
47
49
41
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-144
STEP 6. Check the wiring harness between hood switch
connector A-14 (terminal 1) and ETACS-ECU connector D-
223 (terminal 48).
NOTE: Also check intermediate connector D-27 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector D-27 is damaged, Repair
or replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between hood switch connector A-
14 (terminal 1) and ETACS-ECU connector D-223
(terminal 48) in good condition?
YES : Replace the ETACS-ECU. If the theft-alarm system
operates normally, it indicates that a correct signal is
sent from the hood switch.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. If the theft-
alarm system operates normally, it indicates that a
correct signal is sent from the hood switch.
AC204167
CONNECTOR : A-14
HARNESS
SIDE
A-14(B)
A-14(B)
AC
1
2
AC204174
CONNECTOR : D-223
AC
D-223(B)
D-223(B)
HARNESS SIDE
42
43
50
51
45
46
53
54
52
44
48
5655
47
49
41
AC204170
CONNECTOR : D-27
AH
10
4
8
7
3
9
5
1
6
2
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-145
INSPECTION PROCEDURE P-10: Transmitter: ETACS-ECU does not receive any signal from the lock,
unlock switch or panic switch.
.
CIRCUIT OPERATION
The ETACS-ECU receives signal through its receiver
from the transmitter, and operates the keyless entry
system according to the signal.
.
TECHNICAL DESCRIPTION (COMMENT)
If the signal is not normal, the systems, which are
described in "CIRCUIT OPERATION", do not work
normally.
.
TROUBLESHOOTING HINTS
• The transmitter may be defective
• The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
STEP 1. Register the transmitter.
Replace the transmitter. Refer to GROUP 42, Keyless Entry
System, On-vehicle Service, How to register secret code
Q: Can the transmitter be registered correctly?
YES : If the systems, which are described in "CIRCUIT
OPERATION", work normally, the input signal from
the transmitter should be normal.
NO : Go to Step 2.
Transmitter Input Circuit
INPUT SIGNAL PROCEDURES
TSB Revision
SWS INPUT SIGNAL PROCEDURES
54Bc-146
STEP 2. Check the transmitter battery.
Measure the voltage of the transmitter battery.
• The voltage should equal approximately 2.5 - 3.2 volts.
Q: Is the measured voltage approximately 2.5 - 3.2 volts?
YES : Go to Step 3.
NO : Replace the battery. If the transmitter can be
registered normally, and the systems, which are
described in "CIRCUIT OPERATION", operate
normally, it indicates that the transmitter is sending
normal signal to the ECU.
STEP 3. Check the transmitter.
Substantial other transmitter in order to register encrypted
code. Refer to GROUP 42, Keyless Entry System, On-vehicle
Service, How to register secret code
Q: Can the transmitter be registered correctly?
YES : If the systems, which are described in "CIRCUIT
OPERATION", work normally, the input signal from
the transmitter should be normal.
NO : Replace the ETACS-ECU. If the systems, which are
described in "CIRCUIT OPERATION", work normally,
the input signal from the transmitter should be normal.
ACX01609
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст