Mitsubishi Montero (2002-2004). Manual — part 665
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-357
STEP 2. Check the continuity at knock sensor harness
side connector B-09.
(1) Disconnect the connector B-09 and measure at the harness
side.
(2) Check for the continuity between terminal No. 2 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 3.
NO : Repair an open circuit or harness damage between
knock sensor connector B-09 (terminal No. 2) and
ground. Then go to Step 6.
STEP 3. Check harness connector D-134 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 6.
AK200961
1
2
CONNECTOR: B-09
B-09(GR)
KNOCK
SENSOR
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01415AN
B-09 HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
AK201166
61
62
63
64
65
66
67
68
69
70
71
76
77
78
79
85
86
87
80
72
73
74
75
81
82
83
84
88
89
CONNECTOR: D-134
AB
PCM
D-134(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-358
STEP 4. Check for open circuit, short circuit to ground and
harness damage between knock sensor connector B-09
(terminal No. 1) and PCM connector D-134 (terminal No.
89).
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it. Then go to Step 6.
AK200961
1
2
CONNECTOR: B-09
B-09(GR)
KNOCK
SENSOR
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK201166
61
62
63
64
65
66
67
68
69
70
71
76
77
78
79
85
86
87
80
72
73
74
75
81
82
83
84
88
89
CONNECTOR: D-134
AB
PCM
D-134(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-359
STEP 5. Check the knock sensor.
(1) Disconnect the knock sensor connector B-09.
(2) Start the engine and run at idle.
(3) Measure the voltage between knock sensor side connector
terminal No. 1 (output) and No. 2 (ground).
(4) Gradually increase the engine speed.
• The voltage increases with the increase in the engine
speed.
(5) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : Replace the PCM. Then go to Step 6.
NO : Replace the knock sensor. Then go to Step 6.
STEP 6. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
CAUTION
CAUTIONTo prevent damage to scan tool MB991502,
always turn the ignition switch to the "LOCK" (OFF) posi-
tion before connecting or disconnecting scan tool
MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Erase the DTC.
(4) Test drive under the following conditions:
• Engine speed: 3000 − 5000r/min
• Engine load : 40 % or more
• Drive a minimum of 3 seconds after the above condi-
tions have been met.
(5) After completing the test drive, read the DTC.Turn the
ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0325 set?
YES : The inspection is complete.
NO : Retry the troubleshooting.
AK200961
1
2
CONNECTOR: B-09
B-09(GR)
KNOCK
SENSOR
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
ACX01539
16-PIN
MB991502
AC
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-360
DTC P0335: Crankshaft Position Sensor Circuit
WHITE-
BLA
CK
WHITE-
BLA
CK
RED
AK201142
SKY B
ULE
BLUE-RED
MFI RELAY
BATTERY
70
88
3
2
1
3 4
1 2
B-22X
5V
POWERTRAIN
CONTROL
MODULE (PCM)
3
1 2
B-36
MU802603
3
2
1
4
CRANKSHAFT
POSITION
SENSOR
Crankshaft Position Sensor Circuit
61
656667686970 717273
74757677787980 8182
8384
858687
8889
62
6364
D-134
(MU803804)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст