Mitsubishi Montero (2002-2004). Manual — part 957
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-311
STEP 4. Check joint connector D-01, junction block
connector D-208, D-212, intermediate connector E-11 and
transfer shift lever switch connector E-116 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
AC204170
CONNECTOR : D-01
CD
9 10
8
6 7
31 32
30
29
18 19 20 21
5
4
2
1
3
27
26
24
23
25
12 13 14 15 16 17
28
11
22
33
AC204191
CONNECTORS : D-208, D-212
5 6
2
4
3
1
JUNCTION BLOCK
(FRONT VIEW)
3
10
9
4
11
8
7
1
5
2
6
D-208
D-208
D-212
D-212
AS
AC204176
CONNECTOR : E-11
AZ
3
10
16
9
7 8
6
1
4
2
5
11
14
1213
15
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-312
Q: Are the connectors and terminals in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 5. Check harness for open circuit or short circuit to
ground between junction block connector D-208 terminal 2
and transfer shift lever switch connector E-116 terminal 1.
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair or replace the harness wire.
AC204175
CONNECTOR : E-116
AH
6
2
5
4
3
1
AC204173
CONNECTOR : D-208
BA
5 6
2
4
3
1
JUNCTION BLOCK
(FRONT VIEW)
AC204175
CONNECTOR : E-116
AH
6
2
5
4
3
1
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-313
STEP 6. Measure the switch output voltage at transfer-ECU
connector E-109 by backprobing.
(1) Disconnect connector E-109 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 20 (Transfer shift
lever position: 2H) and ground by backprobing. [terminal 21
(Transfer shift lever position: 4H), terminal 22 (Transfer shift
lever position: 4HLc), terminal 23 (Transfer shift lever
position: 4LLc) and ground by backprobing.]
• The voltage should measure battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 9.
NO : Go to Step 7.
STEP 7. Check transfer-ECU connector E-109 and transfer
shift lever switch connector E-116 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204176
CONNECTOR : E-109
BB
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
AC204918 CG
E-109 HARNESS CONNECTOR :
HARNESS SIDE
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
AC204176
CONNECTOR : E-109
BB
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
AC204175
CONNECTOR : E-116
AH
6
2
5
4
3
1
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-314
STEP 8. Check harness for open circuit or short circuit to
ground between transfer-ECU connector E-109 terminal 20
(21, 22 and 23) and transfer shift lever switch connector E-
116 terminal 3 (5, 6 and 2).
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair or replace the harness wire.
STEP 9. Check transfer-ECU connector E-109 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204176
CONNECTOR : E-109
BB
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
AC204175
CONNECTOR : E-116
AH
6
2
5
4
3
1
AC204176
CONNECTOR : E-109
BB
11 12
25
24
13
26
9
22
7
6
20
19
8
21
10
23
5
4
17
2
1
15
14
3
16
18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст