Mitsubishi Montero (2002-2004). Manual — part 416
ON-VEHICLE SERVICE
TSB Revision
WHEEL AND TIRE
31-7
ON-VEHICLE SERVICE
TIRE INFLATION PRESSURE CHECK
M1311000900259
NOTE: For information on tire inflation pressure, refer to the
label attached to the center pillar on the driver's side.
TIRE WEAR CHECK
M1311001000260
Measure the tread depth of the tires.
Minimum limit: 1.6 mm (0.06 inch)
If the remaining tread depth is less than the minimum limit,
replace the tire.
NOTE: When the tread depth of the tires is reduced to 1.6 mm
(0.06 inch) or less, wear indicators will appear.
WHEEL RUNOUT CHECK
M1311001100267
Jack up the vehicle so that the wheels are clear of the floor.
While slowly turning the wheel, measure wheel runout with a
dial indicator.
Limit:
Radial runout; 1.0 mm (0.04 inch) or less
Lateral runout; 1.0 mm (0.04 inch) or less
If wheel runout exceeds the limit, replace the wheel.
WHEEL AND TIRE
INSTALLATION SERVICE POINT
M1311001300227
Ground Wheel and Tire
Tighten the wheel nuts to the specified torque.
Tightening torque: 108
± 10 N⋅m (80 ± 7 ft-lb)
Spare Wheel and Tire
CAUTION
Install the spare tire so that the valve comes to the position
shown in the illustration. If the tire is mounted with the
valve positioning down, water will accumulate at the valve
portion, which may cause corrosion of the valve.
Tighten the lock cylinder and bolt to the specified torque.
Tightening torque: 46
± 8 N⋅m (34 ± 6 ft-lb)
ACX00651AB
LATERAL
RADIAL
ACX00935 AB
SPECIFICATIONS
TSB Revision
WHEEL AND TIRE
31-8
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1311001600262
GENERAL SPECIFICATIONS
M1311000200283
NOTE: PCD (Pitch Circle Diameter) indicates the pitch circle diameter of the wheel installation holes.
SERVICE SPECIFICATIONS
M1311000300309
ITEM
SPECIFICATION
Spare tire lock cylinder
46
± 8 N⋅m (34 ± 6 ft-lb)
Spare tire mounting bolt
46
± 8 N⋅m (34 ± 6 ft-lb)
Wheel nut
108
± 10 N⋅m (80 ± 7 ft-lb)
ITEM
SPECIFICATION
Wheel (including spare wheel)
Type
Aluminum type
Size
16
× 7JJ
Amount of wheel offset mm (in)
46 (1.8)
Pitch circle diameter (PCD) mm (in)
139.7 (5.50)
Tire (including spare tire)
Size
265/70 R16 112S
ITEM
LIMIT
Tread depth of tire mm (in)
Minimum 1.6 (0.06)
Radial-force variation of tire N (lb)
118 (26.5)
Wheel runout (Radial runout) mm (in)
1.0 (0.04) or less
Wheel runout (Lateral runout) mm (in)
1.0 (0.04) or less
33A-1
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
FRONT SUSPENSION DIAGNOSIS .
INTRODUCTION TO FRONT SUSPENSION
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING STRATEGY . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
FRONT WHEEL ALIGNMENT CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
UPPER ARM BALL JOINT END PLAY
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BALL JOINT DUST COVER CHECK . . . . .
UPPER ARM ASSEMBLY . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION . . . . . . . . . . . . . . . . . . . . . . .
BALL JOINT DUST COVER
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
SHOCK ABSORBER ASSEMBLY . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
LOWER ARM . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
BALL JOINT DUST COVER
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
STABILIZER BAR. . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
STABILIZER LINK BALL JOINT DUST COVER
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . .
GENERAL SPECIFICATIONS . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
FRONT SUSPENSION
33A-2
.
GENERAL DESCRIPTION
M1331000100084
This is a coil spring-type double wishbone indepen-
dent-type front suspension. This type of suspension
is rigid, has very little variation in roll center height
and provides excellent riding comfort.
CONSTRUCTION DIAGRAM
FRONT SUSPENSION DIAGNOSIS
INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS
M1332009000184
If the rear suspension is faulty, the vehicle will not
track straight or unusual noise will occur. Incorrect
wheel alignment, malfunction of shock absorber, sta-
bilizer bar, coil spring, control arms or out-of-balance
tires may cause these problems.
TROUBLESHOOTING STRATEGY
M1332009100170
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
rear suspension fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
ACX02227AB
COIL SPRING
No.2 CROSSMEMBER
SHOCK ABSORBER
UPPER ARM
LOWER ARM
STABILIZER BAR
FRONT FRAME
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст