Mitsubishi Montero (2002-2004). Manual — part 506
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-195
2. Press the "ADJ" [NEXT] switch.
The screen is switched to the service mode second menu
screen.
3. Press the function switch 1 [MONITOR]. The screen is
switched to the monitor check mode.
4. When respective function switches are pressed on this
screen, the screen is switched as follows.
• When the function switch 1 [DISP.] is pressed, the screen is
switched to the display check mode.
• When the function switch 2 [COMP.] is pressed, the screen
changes to the geomagnetic sensor check mode.
• When the "ADJ" switch is pressed, the screen changes to
the service mode second menu screen.
.
Display check mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
2. Press the "ADJ" [NEXT] switch is pressed. The screen
changes to the service mode second menu screen.
Service mode
ACX01985
MONITOR
BACK
END
AB
SERVICE MODE SECOND MENU SCREEN
Monitor check mode
ACX02001
BACK
DISP.
COMP.
AB
MONITOR CHECK MODE SCREEN
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Service mode
ACX01985
MONITOR
BACK
END
AB
SERVICE MODE SECOND MENU SCREEN
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-196
3. Press the function switch 1 [MONITOR]. The screen is
switched to the monitor check mode.
4. Press the function switch 1 [DISP] on the monitor check
mode screen. The screen changes to the display check
mode screen. When respective function switches are
pressed on this screen, the screen changes as follows.
• When the function switch 1 [COLOR] is pressed, the color
bar is displayed.
• When the function switch 2 [GRAY] is pressed, the gray
scale is displayed.
• When the function switch 3 [WHITE] is pressed, the white
screen is displayed.
• When the "ADJ" [BACK] is pressed, the service mode dis-
play returns.
.
Monitor check mode
ACX02001
BACK
DISP.
COMP.
AB
MONITOR CHECK MODE SCREEN
WHITE YELLOW LIGHT
BLUE GREEN PURPLE RED BLUE BLACK
ACX02006
BACK
COLOR
GRAY
WHITE
AB
COLOR BAR
WHITE
BLACK
ACX02002
BACK
COLOR
GRAY
WHITE
AC
WHITE
ACX02003
BACK
COLOR
GRAY
WHITE
AB
WHITE
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-197
Geomagnetic sensor check mode
1. Press the "ADJ" switch with the ignition switch at "LOCK"
(OFF) position, and while keeping on pressing, turn the
ignition switch to the "ACC" or "ON" position. When the
"ADJ" switch is pressed continuously for more than five
seconds, the service function is activated at the same time
with the reception signal (pip sound) and the first menu
screen of the service mode is displayed.
2. Press the "ADJ" switch [next].
The screen changes to the service mode second menu
screen.
3. Press the function switch 1 [MONITOR] on the service mode
second menu screen.
The screen is switched to the monitor check mode.
4. Press the function switch 2 [COMP.].
• <Normal case that the body is not magnetized>
The geomagnetic sensor mode screen is displayed. Each of
X- and Y-outputs of the geomagnetic sensor, center coordi-
nates, and radius of the direction circle are displayed. For
degeomagnetization, refer to
.
• <Case that the body is magnetized>
If the sensor value is outside the range between 450 and
580, it is meant that the body is magnetized. The screen
that calls upon to demagnetize the body stating "Demagne-
tize within range of acceptable level" is displayed. In this
case, it is necessary to demagnetize the body and to cor-
rect the geomagnetic sensor. Refer to on-vehicle service-
vehicle magnetic compensation
.
Service mode
ACX01984
AUTO
DIAG.
HISTORY
NEXT
END
AE
SERVICE MODE FIRST MENU SCREEN
Service mode
ACX01985
MONITOR
BACK
END
AB
SERVICE MODE SECOND MENU SCREEN
Monitor check mode
ACX02001
BACK
DISP.
COMP.
AB
MONITOR CHECK MODE SCREEN
Geomagnetic sensor
Sensor level
X=XXX, Y=XXX
Acceptable X, Y range: (301-722)
Coordi. of C. C. X=XXX, Y=XXX
Radius of D. C. X=XXX,Y=XXX
ACX02004
CAL.COMP
BACK
AC
Geomagnetic sensor
Sensor level
X=XXX, Y=XXX
Acceptable X, Y range: (301-722)
Demagnetise within
range of acceptable level.
AC001241
CAL.COMP
BACK
AC
(430 - 581)
RV METER
TSB Revision
CHASSIS ELECTRICAL
54A-198
• When function switch 1 [CAL.COMP] is pressed at the pre-
vious screen, a message of urging rotation compensation is
displayed. For the method of magnetization compensation
by rotation, refer to
.
Release of service mode
The service mode is released by pressing the "DISP" switch
[END] is pressed on the service mode first screen or the ser-
vice mode second screen, or by turning the ignition switch to
the "LOCK" (OFF) position.
BATTERY DISCONNECTION
When the battery cable is disconnected, the stored data may
disappear. In that case, the system connection should be
checked using the procedure described below
.
Checking connection of system
When the connection data has disappeared, turning the ignition
key to "ACC" position will make the following message appear.
1. Start the engine (or turn the ignition key to "ON" position).
2. When the engine is started or when the ignition key is in the
"ON" position, the monitor will display the message.
3. After a short while the system will beep. When the
connection is completed, the message will be displayed.
Stat to check the system.
Please turn the ignition key
to the "ON"position
AC001555AB
Checking the system connection.
Please wait!
AC001553AB
Completed the system connection.
AC001554 AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст