Mitsubishi Montero (2002-2004). Manual — part 905
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-103
STEP 10. Check harness for open circuit or short circuit to
ground between transmission range switch connector C-
04 terminal 1 and PCM connector D-134 terminal 66.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair or replace the harness wire.
AC204395
CONNECTOR : C-04
AF
C-04 (B)
4
9
5
10
3
8
2
7
6
1
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-104
STEP 11. Check combination meter connector D-32 and
intermediate connector E-113 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 12.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 12. Check harness for short circuit to ground
between combination meter connector D-32 terminal 1 and
intermediate connector E-114 terminal 22.
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair or replace the harness wire.
AC204170
CONNECTOR : D-32
CF
D-32 (GR)
10
9
23
22
12
11
25
24
8
6 7
20
13
5
4
18
17
19
21
16
3
2
15
14
1
AC204176
CONNECTOR : E-113
BC
1
6
2
7 8 9 10 11 12 13 14
3 4 5
AC204170
CONNECTOR : D-32
CF
D-32 (GR)
10
9
23
22
12
11
25
24
8
6 7
20
13
5
4
18
17
19
21
16
3
2
15
14
1
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-105
STEP 13. Check PCM connector D-134 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 14. Check the transmission range switch.
Measure the resistance between the terminals for each selec-
tor position as indicated in the table above.
Q: Does the resistance measure less than 2 ohms for each
selector position?
YES : Go to Step 15.
NO : Replace the transmission range switch. Refer to
GROUP 23B, Transmission
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
TRANSMISSION
RANGE
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
1
− 7
Less than 2 ohms.
R
7
− 8
N
2
− 7
D
3
− 7
ACX01187AD
P
R
N
D
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-106
STEP 15. Check transmission range switch connector C-04
the for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 16.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 16. Measure the transmission range switch output
voltage at PCM connector D-134 by backprobing.
(1) Do not disconnect connector D-134.
(2) Turn the ignition switch to the "ON" position.
(3) Move the selector lever to the "R" position.
(4) Measure the voltage between terminal 67 and ground by
backprobing.
• The voltage should measure battery positive voltage.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Does the voltage measure battery positive voltage?
YES : Go to Step 13.
NO : Go to Step 17.
AC204395
CONNECTOR : C-04
AF
C-04 (B)
4
9
5
10
3
8
2
7
6
1
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BG
D-134 HARNESS CONNECTOR :
HARNESS SIDE
76
85
65
72
71
73
82
75
81
74
63 64
66
70
69
68
67
78
87
79
88 89
80
77
86
62
61
83 84
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст