Mitsubishi Pajero Pinin. Manual — part 324
CHASSIS ELECTRICAL –
Ignition Switch and Immobilizer System
54A-12
CHECK AT IMMOBILIZER-ECU
TERMINAL VOLTAGE CHECK CHART
Terminal No.
Signal
Checking requirements
Terminal voltage
1
Immobilizer-ECU power supply
Ignition switch: ON
System voltage
2
–
–
–
3
Engine-ECU
–
–
4
Immobilizer-ECU earth
Always
0 V
CHASSIS ELECTRICAL –
Ignition Switch and Immobilizer System
54A-13
IGNITION SWITCH AND IMMOBILIZER SYSTEM
REMOVAL AND INSTALLATION
Caution: SRS
Before removal of air bag module and clock spring, refer to GROUP 52B – Service Precautions
and Air Bag Module and Clock Spring.
Pre-removal and Post-installation Operation
Clock Spring and Column Switch Removal and
Installation (Refer to GROUP 52B – Air Bag Modules
and Clock Spring.)
4
5
6
7
2
1
3
Section A – A
Clip
A
A
Section B – B
Section C – C
Tab
Tab
Instrument panel
B
B
C
C
A
A
1
2
3
2
3
Removal steps
1. Instrument under cover
2. Column cover, lower
3. Column cover, upper
4. Ignition switch
A
A
"
5. Steering lock cylinder
6. Immobilizer-ECU
7. Key reminder switch
CHASSIS ELECTRICAL –
Ignition Switch and Immobilizer System
54A-14
REMOVAL SERVICE POINTS
A
A
"
STEERING LOCK CYLINDER REMOVAL
1.
Insert the key in the steering lock cylinder and turn it to
the “ACC” position.
2.
Using a cross-tip (+) screwdriver (small) or a similar tool,
push the lock pin of the steering lock cylinder inward and
then pull the steering lock cylinder toward you.
INSPECTION
IGNITION SWITCH CONTINUITY CHECK
1.
Remove the column cover lower and upper.
2.
Disconnect the wiring connector from the ignition switch.
3.
Operate the switch, and check the continuity between
the terminals.
Ignition key
iti
Terminal No.
g
y
position
1
2
4
5
6
LOCK
ACC
ON
START
KEY REMINDER SWITCH CONTINUITY CHECK
Disconnect the key reminder switch connector with the switch
attached to the vehicle, and then check the continuity between
the terminals.
Ignition key
Terminal No.
g
y
4
6
Removed
Inserted
Cross-tip (+) screwdriver
CHASSIS ELECTRICAL –
Ignition Switch and Immobilizer System
54A-15
ENCRYPTED CODE REGISTRATION METHOD
AND RESETTING THE CODE TO THE FACTORY
SETTING
Register the encrypted code in the immobilizer-ECU and then
reset the code to the factory setting after parts have been
replaced.
Replacement part
Encrypted code
Ignition key
Necessary
Immobilizer-ECU
Necessary
Engine-ECU*
Necessary
NOTE
*: If the engine-ECU is replaced, the immobilizer-ECU and
ignition key should be replaced together with it.
Each engine-ECU has an individual information for
immobilizer-ECU, and the individual information is registered
in the immobilizer-ECU and ignition key.
ENCRYPTED CODE REGISTRATION METHOD
If using an ignition key that has just been newly purchased,
or if the immobilizer-ECU has been replaced, you will need
to register the encrypted codes for each ignition key being
used into the immobilizer-ECU. (A maximum of eight different
encrypted codes can be registered.)
Moreover, when the immobilizer-ECU has been replaced, you
will need to use the MUT-
II
to input the vehicle secret code
and to register the password (secret code) that the user
specifies into the immobilizer-ECU. (Refer to the “MUT-
II
REFERENCE MANUAL” or “MUT-
II
OPERATING IN-
STRUCTIONS”)
Caution
If registering of the encrypted codes is carried out after
all previously-registered codes have been erased, you
should have ready all of the ignition keys that have already
been registered.
1.
Connect the MUT-
II
to the diagnosis connector.
Caution
Turn the ignition switch to LOCK (OFF) position before
connection or disconnection of the MUT-
II
.
2.
Check that the diagnosis code No.54 is not being generated
by the engine-ECU. If it is being generated check according
to the Troubleshooting Procedures.
3.
Use the ignition key that is to be registered to turn on
the ignition switch.
MUT-
II
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст