Mitsubishi Pajero Pinin. Manual — part 2
GENERAL –
Vehicle Identification/Major Specifications
00-15
ENGINE MODEL NUMBER
1.
The engine model number is stamped on the cylinder
block as shown below.
Engine model
Engine displacement m
ȏ
4G93
1,834
2.
The engine serial number is stamped near the engine
model number.
Engine serial number
AA0201 to YY9999
MAJOR SPECIFICATIONS
2
5
7
9
4
1
8
6
3
<R.H. drive
vehicles>
<L.H. drive
vehicles>
GENERAL –
Major Specifications
00-16
Items
H66WMNJCLA
H66WMNJCRA
H66WMRJCLA
H66WMRJCRA
Vehicle
di
i
Overall length
1 3,735/3,765*
1
dimensions
mm
Overall width
2 1,695
mm
Overall height (unladen)
3 1,695/1,735*
2
/1,705*
3
Wheelbase
4 2,280
Track-front
5 1,435
Track-rear
6 1,445
Overhang-front
7 755/785*
1
Overhang-rear
8 700
Ground clearance
(unladen)
9 200
Vehicle
i ht k
Kerb weight
1,285
1,305
weight kg
Max. gross vehicle weight
1,690
1,700
Max. axle weight
rating-front
740
750
Max. axle weight
rating-rear
545
555
Seating capacity
4
Engine
Model No.
4G93
g
Total displacement m
ȏ
1,834
Transmis-
i
Model No.
V5M21
V4AW4
V5M21
V4AW4
sion
Type
5-speed
manual
4-speed
automatic
5-speed
manual
4-speed
automatic
Fuel system
Fuel supply system
Gasoline Direct Injection
NOTE:
*
1
: Vehicles with bumper extension
*
2
: Vehicles with roof rails
*
3
: Vehicles with roof spoiler
GENERAL –
Precautions Before Service
00-17
PRECAUTIONS BEFORE SERVICE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
1.
Items to follow when servicing SRS
(1) Be sure to read GROUP 52B – Supplemental Restraint System (SRS).
For safe operations, please follow the directions and heed all warnings.
(2) Wait at least 60 seconds after disconnecting the battery cable before doing any further work.
The SRS is designed to retain enough voltage to deploy the air bags even after the battery has
been disconnected. Serious injury may result from unintended air bag deployment if work is done
on the SRS immediately after the battery cable is disconnected.
(3) Warning/caution labels must be heeded when servicing or handling SRS components.
Warning/caution labels are attached in the following locations.
D
Sun visor
D
Glove box
D
SRS air bag control unit (SRS-ECU)
D
Steering wheel
D
Steering gear box
D
Driver’s and passenger’s air bag modules
D
Clock spring
D
Side air bag modules
D
Side impact sensors
D
Instrument panel
D
Hood
D
Seat belt with pre-tensioner
(4) Always use the designated special tools and test equipment.
(5) Store components removed from the SRS in a clean and dry place.
The air bag modules should be stored on a flat surface and placed so that the deployment surfaces
are facing upward.
Do not place anything on top of them.
(6) Never attempt to disassemble or repair the SRS components (SRS air bag control unit, air bag
modules, clock spring and side impact sensors). If faulty replace them.
(7) Whenever you finish servicing the SRS, check the SRS warning lamp operation to make sure
that the system functions properly.
(8) Be sure to deploy the air bag before disposing of the air bag modules or disposing of a vehicle
equipped with air bag. (Refer to GROUP 52B – Air Bag Module Disposal Procedures.)
2.
Observe the following when carrying out operations on places where SRS components are installed,
including operations not directly related to the SRS air bag.
(1) When removing or installing parts do not allow any impact or shock to the SRS components.
(2) SRS components should not be subjected to heat over 93
_
C, so remove the SRS components
before drying or baking the vehicle after painting.
After re-installing them, check the SRS warning lamp operation to make sure that the system
functions properly.
GENERAL –
Precautions Before Service
00-18
SERVICING THE ELECTRICAL SYSTEM
Before replacing a component related to the electrical system
and before undertaking any repair procedures involving the
electrical system, be sure to first disconnect the negative (–)
cable from the battery in order to avoid damage caused by
short-circuiting.
Caution
Before connecting or disconnecting the negative (–) cable,
be sure to turn off the ignition switch and the lighting
switch.
(If this is not done, there is the possibility of semiconductor
parts being damaged.)
APPLICATION OF ANTI-CORROSION AGENTS
AND UNDERCOATS
If oil or grease gets onto the oxygen sensor, it will cause
a drop in the performance of the sensor.
Cover the oxygen sensor with a protective cover when applying
anti-corrosion agents and undercoats.
PRE-INSPECTION CONDITION
“Pre-inspection condition” refers to the condition that the vehicle
must be in before proper engine inspection can be carried
out. If you see the words “Set the vehicle to the pre-inspection
condition”. in this manual, it means to set the vehicle to the
following condition.
D
Engine coolant temperature: 80 to 90
_
C
D
Lamps, electric cooling fan and all accessories: OFF
D
M/T: Neutral
D
A/T: P range
VEHICLE WASHING
If high-pressure car-washing equipment or steam car-washing
equipment is used to wash the vehicle, be sure to note the
following information in order to avoid damage to plastic
components, etc.
D
Spray nozzle distance: Approx. 40 cm or more
D
Spray pressure: 3,900 kPa or less
D
Spray temperature: 82
_
C or less
D
Time of concentrated spray to one point: within 30 sec.
Approx.
40 cm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст