Mitsubishi Pajero Pinin. Manual — part 5
GENERAL –
Support Locations for Lifting and Jacking
00-27
SUPPORT POSITIONS AND SUPPORT METHOD
FOR AN H-BAR LIFT
Caution
When service procedures require removing the rear
suspension, fuel tank, spare tyre and rear bumper, place
additional weight on rear end of vehicle or anchor vehicle
to hoist to prevent tipping of centre of gravity changes.
When H-bar lift is used to lift up vehicles, use of metallic
attachment attached to the H-bar lift may cause damage to
the suspension arm etc. Therefore, lift up the vehicle by the
following procedure.
1.
Place the vehicle on the H-bar lift (same direction).
2.
Place attachments on the H-bar lift at the designated
chassis-support positions. When making the attachments,
refer to the section concerning making them.
Caution
If support is at any location other than the designated
positions, the body or suspension might be deformed
or otherwise damaged, so care should be taken to
support only at the correct (designated) positions.
3.
Raise the H-bar lift to the height at which the vehicle is
slightly raised and check to be sure that the vehicle is
correctly and sufficiently secured; then raise the vehicle.
H-bar lift
H-bar lift
A
Chassis-sup-
port position
(side sill)
Attachment
H-bar lift
Section A–A
Side sill
Attachment
H-bar lift
A
GENERAL –
Support Locations for Lifting and Jacking
00-28
PREPARATION OF “ATTACHMENTS”
1.
Prepare the blocks (wooden) and nails as shown in the
figure.
Item
Dimensions mm
Quantity
Block (A)
90
×
95
×
1,800
2
Block (B)
60
×
100
×
95
4
Block (C)
140
×
40
×
95
8
Nail
70 or more
32
Caution
The wood selected for the blocks must be hard.
2.
For the (B) blocks and (C) blocks, use a saw and chisel
or similar tool to make grooves of the dimensions shown
in the figure.
3.
Make four “ATTACHMENTS” such as shown in the figure
nailing (B) and (C) blocks so that each (B) blocks is
sandwiches between (C) blocks.
Block (A)
mm
1,800
90
95
Block (B)
Block (C)
15
40
60
100
40
20
15
40
140
40
20
40
Block (C)
140
100
Block (C)
Nail
Block (B)
Finished attachment
Movable according
to vehicle width
GENERAL –
Standard Part/Tightening-Torque Table
00-29
STANDARD PART/TIGHTENING-TORQUE TABLE
Each torque value in the table is a standard value
for tightening under the following conditions.
(1) Bolts, nuts and washers are all made of steel
and plated with zinc.
(2) The threads and bearing surface of bolts and
nuts are all in dry condition.
The values in the table are not applicable:
(1) If toothed washers are inserted.
(2) If plastic parts are fastened.
(3) If bolts are tightened to plastic or die-cast
inserted nuts.
(4) If self-tapping screws or self-locking nuts are
used.
Standard bolt and nut tightening torque
Thread size
Torque Nm
Bolt nominal
diameter (mm)
Pitch (mm)
Head mark “4”
Head mark “7”
Head mark “8”
M5
0.8
2.5
4.9
5.9
M6
1.0
4.9
8.8
9.8
M8
1.25
12
22
25
M10
1.25
24
44
52
M12
1.25
41
81
96
M14
1.5
72
137
157
M16
1.5
111
206
235
M18
1.5
167
304
343
M20
1.5
226
412
481
M22
1.5
304
559
647
M24
1.5
392
735
853
Flange bolt and nut tightening torque
Thread size
Torque Nm
Bolt nominal
diameter (mm)
Pitch (mm)
Head mark “4”
Head mark “7”
Head mark “8”
M6
1.0
4.9
9.8
12
M8
1.25
13
24
28
M10
1.25
26
49
57
M10
1.5
24
44
54
M12
1.25
46
93
103
M12
1.75
42
81
96
GENERAL –
Vehicle Identification
GENERAL –
Vehicle Identification
00-1
GROUP 00
GENERAL
VEHICLE IDENTIFICATION
MODELS
Model code
Engine model
Transmission model
Fuel supply system
H67
WMNJCLA
4G94-DOHC (1,999 mL)
V5M21 <5M/T>
GDI
WMNJCRA
WMRJCLA
V4AW4 <4A/T>
WMRJCRA
H77
WLNJCLA
V5M21 <5M/T>
WLNJCRA
WRNJCLA
V4AW4 <4A/T>
WRNJCRA
MODEL CODE
No.
Items
Contents
1
Development
H6:
MITSUBISHI PAJERO
PININ Short wheelbase
H7:
MITSUBISHI PAJERO
PININ Long wheelbase
2
Engine type
7:
2,000 mL petrol engine
3
Sort
W:
Wagon
4
Body style
M:
3-door
L:
5-door
5
Transmission type
N:
5-speed manual
transmission
R:
4-speed automatic
transmission
6
Trim level
J:
GL
7
Specification engine
feature
C:
GDI-DOHC
1
2 3 4 5 6 7 8 9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст