Mitsubishi Pajero Pinin. Manual — part 201
FRONT AXLE
–
Drive Shaft
26-23
3.
Position the plastic boot small end so that one drive shaft
groove is visible.
4.
Turn the adjusting bolt of the special tool so that the
opening distance (W) meets the standard value.
Standard value (W):
2.9
mm
<More than 2.9
mm>
Tighten the adjusting bolt.
<Less than 2.9
mm>
Loosen the adjusting bolt
NOTE
(1) Turning the adjusting bolt changes the opening
distance (W) by approx. 0.7 mm.
(2) Do not turn the adjusting bolt more than one turn.
5.
Butt the boot band (small) against the boot end projection
so that a certain clearance (A) is obtained.
6.
Use the special tool to crimp the boot band (small).
Caution
(1) Secure the drive shaft in an upright position and
clamp the part of the B.J. boot band to be crimped
securely in the jaws of the special tool.
(2) Crimp the B.J. boot band until the special tool
stopper closes.
(W)
MB991561
Stopper
Adjusting bolt
Boot
Boot band (small)
Projection
A
MB991561
FRONT AXLE
–
Drive Shaft
26-24
7.
Check that the crimping amount (B) of the B.J. boot band
is at the standard value.
Standard value (B): 2.4 – 2.8 mm
<If the crimping amount is larger than 2.8 mm>
Readjust the value of (W) in step 4 according
to the following formula, and then repeat the
operation in step 6.
W = 5.5 mm – B
Example: If B = 2.9 mm, then W = 2.6 mm.
<If the crimping amount is smaller than 2.4 mm>
Remove the B.J. boot band, readjust the value
of (W) in step 4 according to the following
formula, and then repeat the operations in
steps 5 and 6 using a new B.J. boot band.
W = 5.5 mm – B
Example: If B = 2.3 mm, then W = 3.2 mm.
8.
Check that the B.J. boot band is not sticking out past
the place where it has been installed.
If the B.J. boot band is sticking out, remove it and then
repeat the operations in steps 4 to 7 using a new B.J.
boot band.
9.
Fill the inside of the B.J. boot with the specified amount
of the specified grease.
Specified grease: Repair kit grease
Amount to use:
<A/T> 85 g (50 g for joint, 35 g for boot)
<M/T> 110 g (55 g for joint, 55 g for boot)
10. Position the boot so that the difference between the boot
big end and the housing stepped part (C) meets the
standard value.
Standard value
(
C
) :
0.1
–
1.55
mm
11. Follow the same procedure as in step 4 to adjust the
size of the opening (W) on the special tool so that it
is at the standard value.
Standard value (W): 3.2 mm
12. Place the B.J. boot band (large) against the projection
at the edge of the boot, and then secure it so that there
is a clearance left as shown by (D) in the illustration.
13. Use the special tool to crimp the B.J. boot band (large)
in the same way as in step 6.
B
C
Boot
Projection
Boot band (large)
D
FRONT AXLE
–
Drive Shaft
26-25
14. Check that the crimping amount (E) of the B.J. boot band
is at the standard value.
Standard value (E): 2.4 – 2.8 mm
<If the crimping amount is larger than 2.8 mm>
Readjust the value of (W) in step 11 according
to the following formula, and then repeat the
operation in step 13.
W = 5.8 mm – E
Example: If E = 2.9 mm, then W = 2.9 mm.
<If the crimping amount is smaller than 2.4 mm>
Remove the B.J. boot band, readjust the value
of (W) in step 11 according to the following
formula, and then repeat the operations in
steps 12 and 13 using a new B.J. boot band.
W = 5.8 mm – E
Example: If E = 2.3 mm, then W = 3.5 mm.
15. Check that the B.J. boot band is not sticking out past
the place where it has been installed.
If the B.J. boot band is sticking out, remove it and then
repeat the operations in steps 12 to 14 using a new B.J.
boot band.
E
FRONT AXLE –
Main Shaft
26-26
MAIN SHAFT
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
D
Drive Shaft Removal and Installation (Refer to
P.26-19.)
D
Free-wheeling Clutch Housing Assembly Removal
and Installation (Refer to P.26-45.)
D
Gear Oil Draining and Refilling (Refer to P.26-11.)
4
5
88 Nm
2
98 – 118 Nm
3
1
7
9
8
9
6
17 Nm
Sealant:
3M ATD Part No.8661 or equivalent
(Apply to the lip)
(Apply to the lip)
Removal steps
1. Vacuum pipe assembly
2. Vacuum hose assembly
3. Vacuum actuator assembly
4. Inner shaft assembly
5. Front housing assembly
"
C
A
6. Oil seal
A
A
" "
B
A
7. Bearing
8. Main shaft
"
A
A
9. Oil seal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст