Mitsubishi Pajero Pinin. Manual — part 370
HEATER, AIR CONDITIONER AND VENTILATION
–
Condenser and Condenser
Fan Motor
55-31
REMOVAL SERVICE POINTS
A
A
"
DISCHARGE HOSE DISCONNECTION
Plug the nipples of the disconnected pipe, hose and condenser
assembly to prevent foreign materials from entering.
Caution
Plug the nipples with material that is not permeable to
air as compressor oil and the receiver absorb water vapour
easily.
A
B
"
CONDENSER ASSEMBLY REMOVAL
1.
Remove the mounting bolts from the front side of the
headlamp support member.
2.
Disengage the lower part of the radiator, and then move
the radiator slightly toward the engine.
3.
Raise the condenser assembly to remove from the engine
compartment.
INSTALLATION SERVICE POINT
"
A
A
RECEIVER INSTALLATION
Install the pipe coming from the condenser to the side stamped
“IN”.
INSPECTION
CONDENSER FAN CHECK
Terminals connected to battery
Condenser fan condition
1
2
Operates
HEATER, AIR CONDITIONER AND VENTILATION
–
Refrigerant Line
55-32
REFRIGERANT LINE
REMOVAL AND INSTALLATION
<L.H. DRIVE VEHICLES>
Pre-removal and Post-installation Operation
D
Discharging and Charging of Refrigerant
(Refer to P.55-10.)
D
Engine Cover Removal and Installation
(Refer to GROUP 11 – Engine Assembly.)
D
Air Cleaner Assembly Removal and Installation.
Compressor oil:
ZXL 200PG
3
4
5
Piping connection
OĆring
1
2
HEATER, AIR CONDITIONER AND VENTILATION
–
Refrigerant Line
55-33
<R.H. DRIVE VEHICLES>
Compressor oil:
ZXL 200PG
3
4
5
Piping connection
OĆring
2
Removal steps
A
A
"
1. Pipe assembly
A
A
"
2. Suction hose
A
A
"
3. Discharge hose
4. Liquid pipe
A
A
"
5. Dual pressure switch
REMOVAL SERVICE POINT
A
A
"
HOSE/PIPE DISCONNECTION
Plug the nipples of the disconnected hose, receiver, evaporator
and compressor to prevent foreign materials from entering.
Caution
Plug the nipples with material that is not permeable to
air as compressor oil and the receiver absorb water vapour
easily.
HEATER, AIR CONDITIONER AND VENTILATION
–
Ventilators
55-34
VENTILATORS
Caution: SRS
When removing and installing the floor console assembly from vehicles equipped with SRS, do
not let it bump against the SRS-ECU or the components.
2
3
4
5
6
5
6
1
Rear heater duct B removal steps
D
Front scuff plate, cowl side trim and
center console assembly (Refer to
GROUP 52A – Instrument Panel.)
D
Floor console assembly
(Refer to GROUP 52A.)
D
Front seat
(Refer to GROUP 52A.)
D
Floor carpet
1. Under cover
2. Rear heater duct B
Defroster nozzle and distribution
duct removal steps
D
Instrument panel
(Refer to GROUP 52A.)
3. Defroster nozzle assembly
4. Distribution duct assembly
Foot distribution duct and rear heater
duct A removal steps
D
Floor console assembly
(Refer to GROUP 52A.)
D
Instrument panel assembly
(Refer to GROUP 52A.)
D
Blower motor
(Refer to P.55-25.)
5. Rear heater duct A
6. Foot distribution duct
NOTE
For the center air outlet assembly and the side air outlet
assembly, refer to GROUP 52A – Instrument panel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст