Mitsubishi Pajero Pinin. Manual — part 299
EXTERIOR –
Marks
51-2
INSTALLATION SERVICE POINT
"
A
A
INSTALLATION OF MARK
1.
APPLICATION POSITION
342 mm
R end line
Front fender panel end line
10 mm
(1) Pininfarina mark
2.
INSTALLATION PROCEDURE
(1) Clean the mark installation surfaces on the body with
unleaded petrol.
(2) Peel off the backing paper from the reverse side of the
marks, and then attach the marks to the vehicle body
so that they fit properly into position.
Caution
When attaching the marks, the surrounding
temperature should be 20 – 38
_
C and the air should
be completely free from dust.
If the surrounding temperature is lower than 20
_
C,
the marks and the places on the body where the marks
are to be attached should be heated to 20 – 38
_
C.
When the marks are attached, care should be used
not to allow bubble to enter between tape and the
body.
INTERIOR
Click on the applicable bookmark to selected the required model year
52A-2
INTERIOR
CONTENTS
SPECIAL TOOL
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL*
3
. . . . . . . . . . . . . . . . . . . . . .
FLOOR CONSOLE
7
. . . . . . . . . . . . . . . . . . . . . . . . .
TRIMS
9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSIDE REAR VIEW MIRROR
11
. . . . . . . . . . . . . .
HEADLINING
11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEAT
12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat*
12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Seat
15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEAT BELT
17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat Belt
17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Seat Belt
18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring, side impact sensors and
interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or
maintenance) are indicated in the table of contents by an asterisk (*).
INTERIOR –
Special Tool/Instrument Panel
52A-3
SPECIAL TOOL
Tool
Number
Name
Use
MB990784
Ornament remover
Removal of switch, trim, etc.
INSTRUMENT PANEL
REMOVAL AND INSTALLATION
For installation of the instrument panel, the bolts and screws described below are used. They are indicated
by symbols in the illustration.
Name
Symbol
Size mm (D
×
L)
Colour
Shape
Tapping screw
a
5
12
–
b
5
20
–
c
5
16
–
d
5
16
Black
Washer-assembled screw
e
5
10
–
Washer-assembled bolt
f
6
16
–
g
8
20
–
h
5
12
–
i
6
16
–
D = Thread diameter
L = Effective thread length
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст