Mitsubishi Pajero Pinin. Manual — part 178
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-22
INSPECTION PROCEDURE 10
Large shocks
Probable cause
Shocks accompany shifting from N
→
D, N
→
R and during each upshift and downshift.
D
Malfunction of direct clutch
D
Malfunction of brake No. 3
D
Malfunction of stop lamp switch
D
Malfunction of inhibitor switch
D
Malfunction of forward clutch
D
Malfunction of valve body
D
Malfunction of A/T-ECU
L
: Refer to the Transmission Workshop Manual.
Is there a large shock when shifting
from N
→
R?
Yes
Check the time lag (within 2 seconds).
NG
Check the direct clutch clear-
ance.
L
Check the brake No. 3 clearance.
L
No
OK
Check each accumulator.
L
Is there a large shock when shifting
from N
→
D?
Yes
MUT-
II
SERVICE DATA
D
28 – Stop lamp switch
OK: ON when brake pedal is de-
pressed
OFF when brake pedal is re-
leased
NG
Inspection Procedure 16 – Stop
lamp switch system (Refer to P.
23-26.)
No
OK
Check the kickdown cable.
NG
Repair
OK
Check each modulator valve.
L
Check each check ball.
L
Check each accumulator.
L
MUT-
II
SERVICE DATA
D
37 – Inhibitor switch
OK: MUT-
II
display and selector
lever position should match.
NG
Inspection Procedure 14 – Inhibi-
tor switch system (Refer to P.
23-25.)
OK
Check the time lag (within 2 seconds)
NG
Check the forward clutch clear-
ance.
L
OK
Check each accumulator.
L
Check the trouble symptoms.
NG
Replace the A/T-ECU.
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-23
INSPECTION PROCEDURE 11
Slippage (vibration)
Probable cause
Occurs when a clutch or brake does not fully engage due to low hydraulic pressure
or a worn facing. Appears as vibration when the problem is slight.
D
Malfunction of torque converter
D
Malfunction of direct clutch
D
Malfunction of forward clutch
D
Malfunction of one-way clutch No. 1, No. 2
D
Malfunction of overdrive brake
D
Malfunction of brake No. 1, No. 2, No. 3
D
Malfunction of overdrive one-way clutch
D
Malfunction of A/T-ECU
L
: Refer to the Transmission Workshop Manual.
Does slippage occur both when moving
forward and reversing?
Yes
Check the torque converter.
NG
Replace the torque converter.
L
No
OK
Check the overdrive clutch system.
L
Check the overdrive one-way clutch
system.
L
Does slippage occur in R range?
Yes
Check slippage in 3rd gear in D range.
NG
Check the direct clutch system.
L
No
OK
Check the brake No. 3 system.
L
Does slippage occur in 1st gear?
Yes
Check for slippage in L range.
NG
Check the forward clutch system.
L
No
OK
Check the one-way clutch No. 2 sys-
tem.
L
Does slippage occur in 2nd gear?
Yes
Check for slippage in 2nd gear in 2
range.
NG
Check the brake No. 2 system.
L
No
OK
Check the brake No. 2 system.
L
Check one-way clutch No. 1.
L
Does slippage occur in 3rd gear?
Yes
Check the direct clutch system.
L
No
Check the overdrive brake system.
L
Check the trouble symptoms.
NG
Replace the A/T-ECU.
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-24
INSPECTION PROCEDURE 12
Lockup abnormality
Probable cause
When lockup does not operate even though in the lockup range, and also when
lockup is operating and the engine is idling but then stalls.
D
Malfunction of torque converter
D
Malfunction of valve body
D
Malfunction of A/T-ECU
L
: Refer to the Transmission Workshop Manual.
Is a normal diagnosis code output?
No
To Inspection Chart For Diagnosis
Code (Refer to P. 23-9.)
Yes
Check the solenoid valve No. 3.
NG
Replace the solenoid valve No. 3.
L
OK
Check the lockup control valve.
NG
Replace the lockup control valve.
L
OK
Replace the torque converter.
L
Check the trouble symptoms.
NG
Replace the A/T-ECU.
INSPECTION PROCEDURE 13
Abnormal engine braking
Probable cause
Engine braking effectiveness is poor after downshifting has occurred.
D
Malfunction of overdrive clutch
D
Malfunction of brake No. 1, No. 3
D
Malfunction of valve body
D
Malfunction of A/T-ECU
L
: Refer to the Transmission Workshop Manual.
Poor braking in 1st, 2nd and 3rd gears
Yes
Check the overdrive clutch system.
L
No
Poor braking in 1st gear
Yes
Check the slippage in R range
OK
Malfunction of low modulator valve.
L
No
NG
Check the brake No. 1 system.
L
Check the brake No. 3 system.
L
Check the trouble symptoms.
NG
Replace the A/T-ECU.
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-25
INSPECTION PROCEDURE 14
Inhibitor switch system
Probable cause
If the engine does not start in P or N range, the cause is probably a problem in
the inhibitor switch system.
D
Malfunction of inhibitor switch
D
Malfunction of harness or connector
D
Malfunction of A/T-ECU
MUT-
II
SERVICE DATA
D
37 – Inhibitor switch
OK: MUT-
II
display and selector
lever position should match
OK
Completed
NG
Check the inhibitor switch. (Refer to
P.23-37.)
NG
Replace
OK
Measure at inhibitor switch connector
B-04.
D
Disconnect the connector and
measure at the harness side.
D
Voltage between terminal 1 and
earth (Ignition switch: ON)
OK: System voltage
NG
Check the ignition switch. (Refer to
GROUP 54 – Ignition Switch.)
OK
Check the following connectors:
B-04, D-04
NG
Repair
OK
Check the trouble symptoms.
Check the harness wire between the
inhibitor switch and the A/T-ECU.
NG
Repair
OK
Replace the A/T-ECU.
NG
INSPECTION PROCEDURE 15
Overdrive switch system
Probable cause
If downshifting does not occur when overdrive switch is turned off while driving
in 4th gear, or if shifting to 4th gear is not possible, the cause is probably a problem
in the overdrive switch system.
D
Malfunction of overdrive switch
D
Malfunction of harness or connector
D
Malfunction of A/T-ECU
D
Malfunction of ignition switch
MUT-
II
SERVICE DATA
D
35 – Overdrive switch
OK: MUT-
II
display and overdrive
switch OD/OD-OFF position
should match.
OK
Completed
NG
Check the overdrive switch. (Refer to
P.23-51.)
NG
Replace
OK
Measure at overdrive switch connector
D-35.
D
Disconnect the connector and
measure at the harness side
D
Voltage between terminal 3 and
earth (Ignition switch: ON)
OK: System voltage
OK
Check the following connectors:
D-35, D-34, D-04
NG
Repair
OK
Check the trouble symptoms.
NG
Check the harness wire between the
overdrive switch and the A/T-ECU.
OK
Repair
NG
Check the ignition switch. (Refer to
GROUP 54 – Ignition Switch.)
Replace the A/T-ECU.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст