Mitsubishi Pajero Pinin. Manual — part 328
CHASSIS ELECTRICAL –
Combination Meters
54A-28
FUEL GAUGE RESISTANCE CHECK
1.
Remove the power supply tightening screw.
2.
Use an ohmmeter to measure the resistance value between
the terminals.
Standard value:
Power supply – Earth: 233.3
Ω
Power supply – Fuel gauge: 108.3
Ω
Fuel gauge – Ground: 125.0
Ω
Caution
When inserting the testing probe into the power supply
terminal, be careful not to touch the printed board.
ENGINE COOLANT TEMPERATURE GAUGE
RESISTANCE CHECK
1.
Remove the power supply tightening screw.
2.
Use an ohmmeter to measure the resistance value between
the terminals.
Standard value:
Power supply – Earth: 178.9
Ω
Power supply – Engine coolant temperature gauge:
54
Ω
Engine coolant temperature gauge – Earth:
232.9
Ω
Caution
When inserting the testing probe into the power supply
terminal, be careful not to touch the printed board.
Power supply
Fuel gauge
Earth
Engine coolant
temperature gauge
Earth
Power supply
CHASSIS ELECTRICAL –
Outside Thermo Sensor
54A-29
OUTSIDE THERMO SENSOR
SERVICE SPECIFICATIONS
Items
Standard value
Internal resistance of outside thermo sensor
Ω
At 25
_
Approx. 1,700
OUTSIDE THERMO SENSOR
REMOVAL AND INSTALLATION
Outside thermo sensor
INSPECTION
OUTSIDE THERMO SENSOR INTERNAL RESISTANCE
CHECK
Check the internal resistance of the outside thermo sensor
are at the standard value at temperatures of 25
_
C.
Standard value:
Approx. 1,700
Ω
(at 25
_
C)
Thermometer
Dryer
Sensor
CHASSIS ELECTRICAL –
Headlamp, Front Turn-signal Lamp and Front Fog Lamp
54A-30
HEADLAMP, FRONT TURN-SIGNAL LAMP AND
FRONT FOG LAMP
SERVICE SPECIFICATIONS
Items
Standard value
Limit
Headlamp aiming for low
beam
Vertical direction
60 mm below horizontal (H)
–
beam
Horizontal direction
Position where the 15
_
sloping section
intersects the vertical line (V)
–
Headlamp intensity cd
–
30,000 or more
Front fog lamp aiming
Vertical direction
100 mm below horizontal (H)
–
Horizontal direction
Parallel to direction of vehicle travel
–
SPECIAL TOOL
Tool
Number
Name
Use
MB990784
Ornament remover
Removal of switch garnish
TROUBLESHOOTING
The headlamp, turn-signal lamp and front fog lamp are controlled by the smart wiring system (SWS).
For troubleshooting, refer to GROUP 54B – Troubleshooting.
CHASSIS ELECTRICAL –
Headlamp, Front Turn-signal Lamp and Front Fog Lamp
54A-31
ON-VEHICLE SERVICE
HEADLAMP AIMING
<USING A BEAM SETTING EQUIPMENT>
1.
The headlamps should be aimed with the proper beam
setting equipment, and in accordance with the equipment
manufacture’s instructions.
NOTE
If there are any regulations pertinent to the aiming of
headlamps in the area where the vehicle is to be used,
adjust so as to meet those requirements.
2.
Alternately turn the adjusting screw to adjust the headlamp
aiming. (Refer to P.54A-32.)
<USING A SCREEN>
1.
Inflate the tyres to the specified pressures and there should
be no other load in the vehicles other than driver or
substituted weight of approximately 75 kg placed in driver’s
position.
2.
Put the headlamp leveling switch in “0” position.
3.
Set the distance between the screen and the centre marks
of the headlamps as shown in the illustration.
Screen
5 m
Headlamp centre line
Vehicle centre line
Lamp centre
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст