Mitsubishi Eclipse. Manual — part 585
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-883
STEP 4. Check connector B-14 at the barometric pressure
sensor and connector C-58 at ECM <M/T> or connector
C-55 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 18.
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK300462
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
CONNECTOR: C-55 <A/T>
C-55 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300748
65
43
50
42
49
41
48
60
61
64
46
47
58
59
67
68
45
56
66
52 51
44
53
62
54
63
57
55
CONNECTOR: C-58 <M/T>
AB
C-58 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-884
STEP 5. Using scan tool MB991958, check data list item 25:
Barometric Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
25, Barometric Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
NO : Replace the ECM or PCM. Then go to Step 18.
AK300810
AB
MB991911
16-PIN
MB991827
MB991824
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-885
STEP 6. Check connector B-14 at the barometric pressure
sensor and connector C-58 at ECM <M/T> or connector
C-55 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between barometric pressure
sensor connector B-14 (terminal No. 2) and ECM
connector C-58 (terminal No. 51) <M/T> or PCM
connector C-55 (terminal No. 55) <A/T> because of
open circuit or harness damage. Then go to Step 18.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 18.
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK300462
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
CONNECTOR: C-55 <A/T>
C-55 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300748
65
43
50
42
49
41
48
60
61
64
46
47
58
59
67
68
45
56
66
52 51
44
53
62
54
63
57
55
CONNECTOR: C-58 <M/T>
AB
C-58 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-886
STEP 7. Check the sensor supply voltage at barometric
pressure sensor connector B-14 by backprobing.
(1) Do not disconnect the connector B-14.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground by
backprobing.
• Voltage should be between 4.8 and 5.2 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 12.
NO : Go to Step 8.
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01521AG
1 2 3 4 5 6 7
B-14 HARNESS
CONNECTOR:
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст