Mitsubishi Eclipse. Manual — part 654
ON-VEHICLE SERVICE
TSB Revision
COOLING SYSTEM
14-19
3. Raise the vehicle at the front with a garage jack.
CAUTION
When removing the radiator cap, use care to avoid contact
with hot coolant or steam. Place a shop towel over the cap
and turn the cap counterclockwise a little to let the pres-
sure escape through the vinyl tube. After relieving the
steam pressure, remove the cap by slowly turning it coun-
terclockwise.
4. Remove the radiator cap, radiator drain plug and if equipped
engine coolant drain plug to drain the coolant.
5. Remove the reserve tank and drain the coolant.
6. After completely draining the coolant, reinstall the drain
plugs and flush the engine and radiator using a radiator
cleaning fluid.
7. After the flushing is completed, completely drain the
cleaning fluid and install the radiator and engine drain plugs.
CAUTION
Do not use alcohol or methanol anti-freeze or any engine
coolants mixed with alcohol or methanol anti-freeze. The
use of an improper anti-freeze can cause corrosion of the
aluminum components.
8. By referring to the section on coolant, select an appropriate
concentration for safe operating temperature within the
range of 30 to 60 %. Use special tool MB991871 to refill the
coolant. A convenient mixture is a 50 % water and 50 %
antifreeze solution [freezing point:
−31°C (−32.8 °F)].
Recommended antifreeze:
MITSUBISHI GENUINE Part NO.MD970389 or equiva-
lent
Quantity:
<2.4L Engine> 7.0 dm
3
(7.4 quarts)
<3.0L Engine> 8.0 dm
3
(8.5 quarts)
9. Reinstall the radiator cap.
10.Start the engine and let it warm up until the thermostat
opens.
11.After repeatedly revving the engine up to 3,000 r/min several
times, then stop the engine.
AC106167
GARAGE JACK
AB
AC000106
DRAIN
PLUG
AB
AC106423AB
MB991871
AIR HOSE
ON-VEHICLE SERVICE
TSB Revision
COOLING SYSTEM
14-20
12.Remove the radiator cap after the engine has become cold,
and pour in coolant up to the brim. Reinstall the cap.
CAUTION
Do not overfill the reserve tank.
13.Add coolant to the reserve tank between the "FULL" and
"LOW" mark if necessary.
ENGINE COOLANT CONCENTRATION TEST
M1141001100192
Refer to GROUP 00, RECOMMENDED LUBRICANTS AND
LUBRICANT CAPACITIES TABLE
.
FAN CONTROLLER CHECK
M1141006100120
1. Remove condenser fan motor connector.
2. Start the engine and run it at idle.
3. Turn the A/C switch to ON and maintain the coolant
temperature at 80
°C (176°F) or less.
4. When measuring the voltage between the fan controller-side
connector terminals, check that the value changes
repeatedly as indicated by (1)
− (3) below.
(1) 0 V
(2) 8.2
± 2.6 V
(3) Battery positive voltage
± 2.6 V
5. If the voltage does not repeatedly change as indicated,
replace the radiator fan motor and the fan controller
assembly.
FAN CONTROL RELAY CONTINUITY CHECK
M1141006200138
AC000274 AC
FAN CONTROLLER
BATTERY
VOLTAGE
TERMINAL NO. TO
BE CONNECTED
TO TESTER
CONTINUITY
TEST RESULTS
Not applied
4
− 2
Open circuit
Connect terminal
No.3 and battery (
−)
terminal.
Connect terminal
No.1 and battery (+)
terminal.
4
− 2
Less than 2 ohm
AC102593
FAN CONTROL RELAY
AB
RADIATOR
TSB Revision
COOLING SYSTEM
14-21
RADIATOR
REMOVAL AND INSTALLATION
M1141001500457
Pre-removal Operation
• Engine Coolant Draining [Refer to GROUP 00, Mainte-
nance Service
− Engine Coolant (Change)
Post-installation Operation
• Transmission Fluid Supplying and Checking (Refer to
GROUP 00, Maintenance Service
− Automatic Transmis-
sion Fluid
.)
• Engine Coolant Supplying [Refer to GROUP 00, Mainte-
nance Service
− Engine Coolant (Change)
AC004073
11
12
13
14
15
8
8
3
5
2
4
9
10
6
7
11 N·m
97 in-lb
11 N·m
97 in-lb
11 N·m
97 in-lb
4.9 N·m
43 in-lb
AD
1
RADIATOR REMOVAL STEPS
1.
RADIATOR CAP
2.
DRAIN PLUG
3.
RUBBER HOSE CONNECTION
4.
RESERVE TANK ASSEMBLY
<<A>> >>A<<
5.
RADIATOR UPPER HOSE
<<A>> >>A<<
6.
RADIATOR LOWER HOSE
<<B>>
7.
A/T OIL COOLER HOSE
CONNECTION
8.
RADIATOR SUPPORT
9.
RADIATOR
10. LOWER INSULATOR
11. CONDENSER FAN MOTOR
ASSEMBLY
12. RADIATOR FAN MOTOR
ASSEMBLY
13. FAN
14. RADIATOR FAN MOTOR
15. SHROUD
RADIATOR FAN MOTOR
ASSEMBLY REMOVAL STEPS
1.
RADIATOR CAP
2.
DRAIN PLUG
<<A>> >>A<<
5.
RADIATOR UPPER HOSE
11. CONDENSER FAN MOTOR
ASSEMBLY
12. RADIATOR FAN MOTOR
ASSEMBLY
13. FAN
14. RADIATOR FAN MOTOR
15. SHROUD
RADIATOR REMOVAL STEPS
RADIATOR
TSB Revision
COOLING SYSTEM
14-22
REMOVAL SERVICE POINTS
.
<<A>> RADIATOR UPPER HOSE/RADIATOR LOWER HOSE
DISCONNECTION
Make mating marks on the radiator hose and the hose clamp.
Disconnect the radiator hose.
.
<<B>> A/T OIL COOLER HOSE REMOVAL
After removing the hose from the radiator, plug the hose and
the radiator nipple to prevent dust or foreign particles from get-
ting in.
INSTALLATION SERVICE POINT
.
>>A<< RADIATOR LOWER HOSE/RADIATOR UPPER HOSE
CONNECTION
1. Insert each hose as far as the projection of the water inlet
fitting.
2. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
ACX01828
MATING MARKS
AB
ACX01829AB
PROJECTION
WATER OUTLET
FITTING
MATING
MARKS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст