Mitsubishi Eclipse. Manual — part 913
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-35
18.Turn the transaxle over so that the installation surface of the
torque converter housing is facing up.
Install special tool MD998913 in a dial gauge, and then
move special tool MB991631 <F4A42> or MB991632
<F4A51> and measure its movement.
Standard value of end play (Reference):
1.65
− 2.11 mm (0.065 − 0.083 inch)
19.Select a pressure plate whose thickness corresponds to the
measured amount of movement from the table below.
NOTE: This illustration shows F4A51.
PRESSURE PLATE FOR LOW-REVERSE BRAKE < F4A42>
PRESSURE PLATE FOR OW-REVERSE BRAKE <F4A51>
MOVEMENT
AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
1.3
− 1.5
(0.051
− 0.059)
1.6 (0.063)
L
MD759567
1.5
− 1.7
(0.059
− 0.067)
1.8 (0.071)
1
MD759414
1.7
− 1.9
(0.067
− 0.075)
2.0 (0.079)
0
MD759415
1.9
− 2.1
(0.075
− 0.083)
2.2 (0.087)
2
MD759416
2.1
− 2.3
(0.083
− 0.091)
2.4 (0.094)
4
MD759417
2.3
− 2.5
(0.091
− 0.098)
2.6 (0.102)
6
MD759418
2.5
− 2.7
(0.098
− 0.106)
2.8 (0.110)
8
MD759419
2.7
− 2.9
(0.106
− 0.114)
3.0 (0.118)
D
MD759420
MOVEMENT
AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
1.0
− 1.2
(0.039
− 0.047)
1.6 (0.063)
F
MD759568
1.2
− 1.4
(0.047
− 0.055)
1.8 (0.071)
E
MD759425
1.4
− 1.6
(0.055
− 0.063)
2.0 (0.079)
D
MD759426
1.6
− 1.8
(0.063
− 0.071)
2.2 (0.087)
C
MD759427
AKX01069AB
MD998913
MB991631
<F4A42> OR
MB991632
<F4A51>
AKX01123
<F4A42>
MD998913
MB991631
AB
MOVEMENT
AMOUNT
AKX01124
<F4A51>
MD998913
MB991632
AB
MOVEMENT
AMOUNT
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-36
CAUTION
If necessary, take the measurements in steps 9 to 18 after
replacing the pressure plate, brake plate and brake disc.
20.Remove all parts and special tools that were installed to
take the measurements in steps 9 to 18. Remove and
separate the pressure plate and snap ring chosen in steps
12, 16 and 18.
21.Install the snap ring into the groove of transaxle case output
shaft bore.
22.Use special tools MB990930 and MB990938 to tap the
output shaft bearing outer race in the transaxle case.
CAUTION
Do not reuse the bolt, as it has had sealant applied.
23.Tighten the mounting bolts of the output shaft bearing
retainer to the specified torque.
Tightening torque:
23
± 3 N⋅m (17 ± 2 ft-lb) <F4A42>
54
± 5 N⋅m (40 ± 4 ft-lb) <F4A51>
1.8
− 2.0
(0.071
− 0.079)
2.4 (0.094)
B
MD759428
2.0
− 2.2
(0.079
− 0.087)
2.6 (0.102)
A
MD759429
2.2
− 2.4
(0.087
− 0.094)
2.8 (0.110)
0
MD759430
2.4
− 2.6
(0.094
− 0.102)
3.0 (0.118)
1
MD759431
MOVEMENT
AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
AKX01060
MB990938
MB990930
AB
AKX01038
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-37
24.Use special tool MD998350 to install the collar and taper
roller bearing on the output shaft.
25.Apply ATF to a new jam nut, and use special tools
MB990607 and MB991625 to tighten the jam nut to the
specified torque. Then turn back one turn, and tighten to the
specified torque again.
Tightening torque: 167
± 10 N⋅m (123 ± 7 ft-lb)
NOTE: The jam nut is reverse threaded.
26.Move the output shaft to measure the end play and record
the measurement value.
27.Remove the parts that were installed in steps 22 to 25.
28.Select a spacer whose thickness corresponds to the
measured amount of movement from the following table.
SPACER FOR OUTPUT SHAFT
AKX01061
MD998350
AB
AKX01062
MB991625
MB990607
AB
MOVEMENT
AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
1.81
− 1.85
(0.0713
− 0.0728)
1.88 (0.0740) 88
MD756579
1.85
− 1.89
(0.0728
− 0.0744)
1.92 (0.0756) 92
MD756580
1.89
− 1.93
(0.0744
− 0.0760)
1.96 (0.0772) 96
MD756581
1.93
− 1.97
(0.0760
− 0.0776)
2.00 (0.0787) 00
MD756582
1.97
− 2.01
(0.0776
− 0.0791)
2.04 (0.0803) 04
MD756583
2.01
− 2.05
(0.0791
− 0.0807)
2.08 (0.0819) 08
MD756584
2.05
− 2.09
(0.0807
− 0.0823)
2.12 (0.0835) 12
MD756585
2.09
− 2.13
(0.0823
− 0.0839)
2.16 (0.0850) 16
MD756586
2.13
− 2.17
(0.0839
− 0.0854)
2.20 (0.0866) 20
MD756587
AKX01063
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-38
29.Repeat steps 22 to 25 again, installing each part and using
the appropriate adjustment spacer determined in step 28.
30.Stake the jam nut with a punch (two places).
2.17
− 2.21
(0.0854
− 0.0870)
2.24 (0.0882) 24
MD756588
2.21
− 2.25
(0.0870
− 0.0886)
2.28 (0.0898) 28
MD756589
2.25
− 2.29
(0.0886
− 0.0902)
2.32 (0.0913) 32
MD756590
2.29
− 2.33
(0.0902
− 0.0917)
2.36 (0.0929) 36
MD756591
2.33
− 2.37
(0.0917
− 0.0933)
2.40 (0.0945) 40
MD756592
2.37
− 2.41
(0.0933
− 0.0949)
2.44 (0.0961) 44
MD756593
2.41
− 2.45
(0.0949
− 0.0965)
2.48 (0.0976) 48
MD756594
2.45
− 2.49
(0.0965
− 0.0980)
2.52 (0.0992) 52
MD756595
2.49
− 2.53
(0.0980
− 0.0996)
2.56 (0.1008) 56
MD756596
2.53
− 2.57
(0.0996
− 0.1012)
2.60 (0.1024) 60
MD756597
2.57
− 2.61
(0.1012
− 0.1028)
2.64 (0.1039) 64
MD756598
2.61
− 2.65
(0.1028
− 0.1043)
2.68 (0.1055) 68
MD756599
2.65
− 2.69
(0.1043
− 0.1059)
2.72 (0.1071) 72
MD760685
2.69
− 2.73
(0.1059
− 0.1075)
2.76 (0.1087) 76
MD760686
MOVEMENT
AMOUNT
mm (in)
THICKNESS
mm (in)
ID
SYMBOL
PRESSURE
PLATE
PART NO.
AKX01064
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст