Mitsubishi Eclipse. Manual — part 537
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-691
STEP 22. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern (Refer to
Diagnostic Function
− OBD-ll Drive Cycle − Procedure 1 −
Evaporative Emission System Leak Monitor
(2) Read the diagnostic trouble code.
Q: Is diagnostic trouble code P0451 set?
YES : Go to Step 2.
NO : This diagnosis is complete.
DTC P0452: Evaporative Emission Control System Pressure Sensor Low Input
AC001944
CHECK VALVE A
CHECK
VALVE B
EVAPORATIVE
EMISSION CANISTER
FUEL TANK
EVAPORATIVE
EMISSION
VENTILATION
SOLENOID
EVAPORATIVE EMISSION
PURGE SOLENOID
INTAKE MANIFOLD
SYSTEM DIAGRAM <VEHICLES WITHOUT INTAKE MANIFOLD TUNING SYSTEM>
A
B
C
D
E
F
G
Q
R
I
H
K
J
L
N
O
M
P
AG
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-692
AC106496
CHECK VALVE A
CHECK
VALVE B
EVAPORATIVE
EMISSION CANISTER
FUEL TANK
EVAPORATIVE
EMISSION
VENTILATION
SOLENOID
EVAPORATIVE EMISSION
PURGE SOLENOID
INTAKE MANIFOLD
SYSTEM DIAGRAM <VEHICLES WITH INTAKE MANIFOLD TUNING SYSTEM>
B
C
E
F
G
Q
R
I
H
K
J
L
N
O
M
P
AE
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-693
Fuel Tank Differential Pressure Sensor Circuit
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-694
.
CIRCUIT OPERATION
• A 5-volt voltage is supplied to the power terminal
of the fuel tank differential pressure sensor (ter-
minal 3) from the ECM (terminal 42) <M/T> or
PCM (terminal 46) <A/T>. The ground terminal
(terminal 2) is grounded with the ECM (terminal
49) <M/T> or PCM (terminal 57) <A/T>.
• A voltage proportional to the pressure in the fuel
tank is sent from the output terminal of the fuel
tank differential pressure sensor (terminal 1) to
the ECM (terminal 93) <M/T> or PCM (terminal
92) <A/T>.
.
TECHNICAL DESCRIPTION
• To judge if the fuel tank differential pressure sen-
sor is defective, the ECM <M/T> or PCM <A/T>
monitors the fuel tank differential pressure sensor
output voltage.
• Based on the test conditions and judgment crite-
ria, the ECM <M/T> or PCM <A/T> judges if the
fuel tank differential pressure sensor output volt-
age is normal.
.
DESCRIPTIONS OF MONITOR METHODS
• Compare purge solenoid status with fuel tank dif-
ferential pressure sensor output voltage.
.
MONITOR EXECUTION
• Continuous.
.
MONITOR EXECUTION CONDITIONS (Other
Monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Evaporative emission purge solenoid monitor
• Evaporative emission ventilation solenoid monitor
AC001741 AJ
CONNECTOR: C-28
AC001689AN
CONNECTORS: C-58, C-62<M/T>,
C-55, C-59 <A/T>
ECM <M/T>
OR
PCM <A/T>
C-62
<M/T>
C-58 <M/T>,
C-59 <A/T>
C-55
<A/T>
AC001991
CONNECTOR: C-90
CONNECTOR
BLOCK (LH)
AI
AC001787AD
CONNECTOR: D-16
AC103356
FUEL TANK
AD
CONNECTOR: D-18
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст