Mitsubishi Eclipse. Manual — part 794
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-185
STEP 40. Check harness for open circuit or short circuit to
ground between transmission range switch connector
B-41 terminal 5 and PCM connector C-61 terminal 109.
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair or replace the harness wire.
AC001844
CONNECTOR: B-41
DIPSTICK
AK
B-41
AC001657
CONNECTOR: C-61
PCM
BH
C-61
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-186
STEP 41. Check the transmission range switch.
Measure the resistance between the terminals for each selec-
tor position as indicated in the table below.
NOTE: For vehicles with sport mode, four positions (P, R, N, D)
are used.
Q: Is the measured resistance less than 2 ohms for each
selector position?
YES : Go to Step 42.
NO : Replace the transmission range switch. Refer to
GROUP 23B, Transaxle
STEP 42. Check transmission range switch connector B-41
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 43.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
SELECTOR
POSITION
TERMINAL CONNECTION
OF TESTER
SPECIFIED
CONDITION
P
3
− 8, 9 − 10
Less than 2 ohms.
R
7
− 8
N
4
− 8, 9 − 10
D
1
− 8
3
5
− 8
2
2
− 8
L
6
− 8
AC004672
DIPSTICK
TRANSMISSION
RANGE SWITCH
AK
AC005865
P
R
N
D
3
2
L
AB
AC001844
CONNECTOR: B-41
DIPSTICK
AK
B-41
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-187
STEP 43. Measure the transmission range switch output
voltage at PCM connector C-61 by backprobing.
(1) Do not disconnect connector C-61.
(2) Turn the ignition switch to the "ON" position.
(3) Move the selector lever to the "2" position.
(4) Measure the voltage between terminal 122 and ground by
backprobing.
• The voltage should measure battery positive voltage.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Does the voltage measure battery positive voltage?
YES : Go to Step 13.
NO : Go to Step 44.
STEP 44. Check PCM connector C-61 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 45.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC001657
CONNECTOR: C-61
PCM
BH
C-61
AC001908AM
C-61 HARNESS
CONNECTOR:
HARNESS SIDE
AC001657
CONNECTOR: C-61
PCM
BH
C-61
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-188
STEP 45. Check harness for open circuit or short circuit to
ground between transmission range switch connector
B-41 terminal 2 and PCM connector C-61 terminal 122.
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair or replace the harness wire.
AC001844
CONNECTOR: B-41
DIPSTICK
AK
B-41
AC001657
CONNECTOR: C-61
PCM
BH
C-61
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст