Mitsubishi Eclipse. Manual — part 308
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-725
STEP 18. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P2228 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P2229: Barometric Pressure Circuit High Input
AK300332
7
4 5 6
1 2 3
GREEN-
YELL
OW
GREEN-
WHITE
BROWN
C-54 <A/T>
(MU803781)
C-60 <M/T>
(MU803772)
ENGINE CONTROL
MODULE (ECM) <M/T>
OR
POWERTRAIN CONTROL
MODULE (PCM) <A/T>
81 <M/T>*1
46 <A/T>*3
5 V
85 <M/T>*1
55 <A/T>*3
40 <M/T>*2
16 <A/T>*4
B-14
BAROMETRIC PRESSURE SENSOR
(INCORPORATED IN VOLUME
AIRFLOW SENSOR)
1
2
5
82
78
81
80
89 90 91 92
79
87
71
74
73
72
76
75
77
85
88
83 84
86
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58 59
60 61 62 63
64 65 66
47
41
Barometric Pressure Sensor Circuit
2
3 4
5 6
7 8
9
11 12 13 14 15 16 17 18 19 20
30
21 22 23
24 25
26 27 28 29
3132 33
34 35
1
10
C-50 <A/T>
(MU803784)
NOTE
*1: ECM connector C-60 <M/T>
*2: ECM connector C-53 <M/T>
*3: PCM connector C-54 <A/T>
*4: PCM connector C-50 <A/T>
C-53 <M/T>
(MU803771)
34
33
32
36
35
37
42
45
31
39
38
46
40 41
43 44
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-726
.
CIRCUIT OPERATION
• A 5-volt voltage is supplied to the barometric
pressure sensor power terminal (terminal No. 1)
from the ECM (terminal No. 81) <M/T> or PCM
(terminal No. 46) <A/T>. The ground terminal
(terminal No. 5) is grounded with ECM (terminal
No. 40) <M/T> or PCM (terminal No. 16) <A/T>.
• A voltage that is proportional to the atmospheric
pressure is sent to the ECM (terminal No. 85)
<M/T> or PCM (terminal No. 55) <A/T> from the
barometric pressure sensor output terminal (ter-
minal No. 2).
.
TECHNICAL DESCRIPTION
• The barometric pressure sensor outputs a volt-
age which corresponds to the barometric pres-
sure.
• The ECM <M/T> or PCM <A/T> checks whether
this voltage is within a specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Barometric pressure sensor output voltage is out of
reasonable barometric pressure range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK300053
CONNECTOR: B-14
AC
BAROMETRIC
PRESSURE
SENSOR
B-14 (B)
AK300060
ECM
CONNECTORS: C-53, C-60 <M/T>
AN
C-53 (G)
C-60 (G)
AK300060
PCM
CONNECTORS: C-50, C-54 <A/T>
AO
C-54 (GR)
C-50 (GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-727
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the start-
ing sequence was completed.
• Battery positive voltage is higher than 8 volts.
Judgement Criteria
• Barometric pressure sensor output has continued
to be 113 kPa (33.4 in.Hg) or higher approxi-
mately 4,000 ft below sea level for 10 seconds.
.
OBD-ll DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-ll Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Barometric pressure sensor failed.
• Open barometric pressure sensor circuit, or con-
nector damage.
• ECM failed. <M/T>
• PCM failed. <A/T>
DIAGNOSIS
Required Special Tools:
• MB991958 (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991911: Main Harness B
START
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
NO
YES
AK301456
MONITORING
CONDITIONS
BAROMETRIC PRESSURE
< 50kPa (14.8in.Hg)
BAROMETRIC PRESSURE
> 113kPa (33.4in.Hg)
CONTINUOUS
FAILURE FOR 10secs
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-728
STEP 1. Using scan tool MB991958, check data list item 25:
Barometric Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB99150 or
MB9919582.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
25, Barometric Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Measure the sensor output voltage at barometric
pressure sensor connector B-14 by backprobing.
(1) Do not disconnect the connector B-14.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground by
backprobing.
• When altitude is 0 m (0 foot), voltage should be 3.7 and
4.3 volts.
• When altitude is 600 m (1,969 feet), voltage should be
3.4 and 4.0 volts.
• When altitude is 1,200 m (3,937 feet), voltage should be
3.2 and 3.8 volts.
• When altitude is 1,800 m (5,906 feet), voltage should be
2.9 and 3.5 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 3.
NO : Go to Step 5.
AK300810
AB
MB991911
16-PIN
MB991827
MB991824
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01520AG
1 2 3 4 5 6 7
B-14 HARNESS
CONNECTOR:
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст