Mitsubishi Eclipse. Manual — part 400
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-143
STEP 13. Check for harness damage between engine
coolant temperature sensor connector B-11 (terminal No.
1) and ECM connector C-58 (terminal No. 44) <M/T> or PCM
connector C-55 (terminal No. 44) <A/T>.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 14.
NO : Repair it. Then go to Step 14.
AK300435
1
2
CONNECTOR: B-11
AB
B-11 (B)
HARNESS CONNECTOR:
COMPONENT SIDE
AK300462
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
CONNECTOR: C-55 <A/T>
C-55 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300748
65
43
50
42
49
41
48
60
61
64
46
47
58
59
67
68
45
56
66
52 51
44
53
62
54
63
57
55
CONNECTOR: C-58 <M/T>
AB
C-58 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-144
STEP 14. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0116 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0117: Engine Coolant Temperature Circuit Low Input
AK000688
1 2
BL
ACK
YELL
O
W
-GREEN
49 <M/T>
57 <A/T>
44
ENGINE CONTROL
MODULE (ECM) <M/T>
OR
POWERTRAIN CONTROL
MODULE (PCM) <A/T>
ENGINE COOLANT
TEMPERATURE SENSOR
B-11
(MU802406)
2
1
5V
65
43
50
42
49
41
48
60 61
64
46 47
58 59
67 68
45
56
66
52
51
44
53
62
54
63
57
55
C-58 <M/T>
(MU803782)
C-55 <A/T>
(MU803781)
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58 59
60 61 62 63
64 65 66
47
41
Engine Coolant Temperature Sensor Circuit
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-145
.
CIRCUIT OPERATION
• 5-volt voltage is applied to the engine coolant
temperature sensor output terminal (terminal No.
1) from the ECM (terminal No. 44) <M/T> or PCM
(terminal No. 44) <A/T> via the resistor in the
ECM <M/T> or PCM <A/T>. The ground terminal
(terminal No. 2) is grounded with ECM (terminal
No. 49) <M/T> or (terminal No. 57) <A/T>.
• The engine coolant temperature sensor is a neg-
ative temperature coefficient type of resistor. It
has the characteristic that when the engine cool-
ant temperature rises the resistor decreases.
• The engine coolant temperature sensor output
voltage increases when the resistor increases
and decreases when the resistor decreases.
.
TECHNICAL DESCRIPTION
• The engine coolant temperature sensor converts
the engine coolant temperature to a voltage and
output it.
• The ECM <M/T> or PCM <A/T> checks whether
this voltage is within a specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Engine coolant temperature sensor output voltage is
out of specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Volume airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
.
AK300081
CONNECTOR: B-11
ENGINE
COOLANT
TEMPERATURE
SENSOR
AB
B-11 (B)
AK300244
CONNECTOR: C-55 <A/T>
AG
PCM
C-55 (GR)
AK300091
CONNECTOR: C-58 <M/T>
ECM
AC
C-58 (GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-146
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the staring
sequence was completed.
Judgement Criteria
• Engine coolant temperature sensor output volt-
age has continued to be 0.1 volt or lower [corre-
sponding to a coolant temperature of 140
°C
(284
°F) or higher] for 2 seconds.
.
OBD-ll DRIVE CYCLE PATTERN
Refer to , Diagnostic Function
− OBD-ll Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Engine coolant temperature sensor failed.
• Shorted engine coolant temperature sensor cir-
cuit connector damage.
• ECM failed. <M/T>
• PCM failed. <A/T>
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
START
OUTPUT VOLTAGE > 4.6V
OUTPUT VOLTAGE < 0.1V
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
CONTINUOUS
FAILURE FOR 2secs
MONITORING
CONDITIONS?
NO
YES
AK301426
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст