Mitsubishi Eclipse. Manual — part 89
OVERALL CONFIGURATION DIAGRAM <ECLIPSE SPYDER>
TSB Revision
CONFIGURATION DIAGRAMS
80A-3
OVERALL CONFIGURATION DIAGRAM
<ECLIPSE SPYDER>
M1801000100332
NOTE:
.
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.
AC101824
FRONT WIRING
HARNESS (RH)
AB
INJECTOR WIRING
HARNESS
INSTRUMENT PANEL
WIRING HARNESS
ROOF WIRING
HARNESS
TRUNK LID
WIRING HARNESS
REAR
BUMPER
WIRING
HARNESS
FLOOR WIRING
HARNESS
FUEL WIRING
HARNESS
DOOR WIRING
HARNESS*
FRONT WIRING
HARNESS (LH)
CONTROL WIRING
HARNESS
BATTERY WIRING
HARNESS
HOW TO READ CONFIGURATION DIAGRAMS
TSB Revision
CONFIGURATION DIAGRAMS
80A-4
HOW TO READ CONFIGURATION DIAGRAMS
M1801000200265
The wiring harness diagrams clearly show the connector locations and harness routings at each site on
actual vehicles.
AC003056
Denotes connector No.
The same connector No. is used throughout the circuit diagrams to facilitate connector location searches.
The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number.
Numbers are usually assigned to parts in clockwise order on the diagram.
Example: A-19
Number specific to connector (serial number)
Connector location site symbol
A: ENGINE COMPARTMENT
B: ENGINE AND TRANSAXLE
C: DASH PANEL
D: FLOOR AND ROOF <ECLIPSE>
D: FLOOR AND WINDSHIELD APERTURE <ECLIPSE SPYDER>
E: DOOR
F: LUGGAGE COMPARTMENT
Denotes ground point.
Same ground number is used throughout circuit
diagrams to facilitate search of ground point.
Refer to GROUP 70 SINGLE PART INSTALLATION
POSITION - GROUND MOUNTING LOCATIONS
for details of ground points.
Denotes the color of the corrugated
tube (If not specified, it is black.)
R: Red
Y: Yellow
The number of connector pins and the connector color
(except milk white)* are shown for ease of retrieval.
Example: (2-B)
Connector color
(milk white if no color is indicated)
Number of connector pins
*: Typical connector colors
B: Black
BR: Brown
Y: Yellow
V: Violet
L: Blue
O: Orange
G: Green
GR: Gray
R: Red
NONE: Milk white
A-15 (2) FOG LIGHT (RH)
A-16 (2-GR) HORN (LOW)
A-17 (2-B) HEADLIGHT (RH)
A-18 (2-B) WINDSHIELD WASHER MOTOR
A-19 (2-GR) DUAL PRESSURE SWITCH
Indicates the device to which the
connector is connected.
The mark shows the
standard mounting position
of wiring harness.
AE
A-17
A-16
A-15
A-18
A-19
Y
Denotes a section covered by a
corrugated tube.
FRONT
WIRING
HARNESS
(RH)
Denotes harness name.
HOW TO READ CONFIGURATION DIAGRAMS
TSB Revision
CONFIGURATION DIAGRAMS
80A-5
NOTES
ENGINE COMPARTMENT
TSB Revision
CONFIGURATION DIAGRAMS
80A-6
ENGINE COMPARTMENT
M1801000300723
AC302546
Connector
symbol
A
AB
A-03
GROUND
CABLE
A-02
A-01
A-37
A-36
A-35
A-34
A-33
A-32
A-31
2
1
FRONT
WIRING
HARNESS
(RH)
A-01
(4-B)
AUTO-CRUISE CONTROL VACUUM
PUMP
A-02
(31-B)
ABS-ECU
A-03
(5-B)
WINDSHIELD WIPER MOTOR
A-04X (4)
FOG LIGHT RELAY
A-05X (4)
HORN RELAY
A-06X (4)
THEFT-ALARM HORN RELAY
<THEFT-ALARM SYSTEM>
A-09X (4)
FAN CONTROL RELAY
A-10X (11)
FRONT-ECU
A-11X (11)
FRONT-ECU
A-12X (1)
ENGINE SPEED DETECTION
CONNECTOR
A-13X (5)
STARTER RELAY <M/T>
A-17X (4)
A/T CONTROL RELAY
A-18X (4)
MFI RELAY
A-19X (4)
A/C COMPRESSOR RELAY
A-22
(2-B)
WHEEL SPEED SENSOR (FRONT:
LH) <ABS>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст