Mitsubishi Eclipse. Manual — part 977
CONVERTIBLE TOP
TSB Revision
BODY
42-133
TOPSTACK SIDE STAY PADS
REMOVAL AND INSTALLATION
M1426205400041
REMOVAL SERVAICE POINT
.
<<A>> TOPSTACK SIDE STAY PAD ASSEMBLY REMOVAL
1. Move the No.1 bow side topstack side stay pad to the outer
side of the vehicle.
Post-installation Operation
• Convertible Top Fit Adjustment (Refer to
AC004136
N
N
N
N
1
AB
REMOVAL STEPS
• DEFOGGER HARNESS
CONNECTOR (REFER TO
• TOP COVER ASSEMBLY (REFER
<<A>> >>A<<
1. TOPSTACK SIDE STAY PAD
ASSEMBLY
REMOVAL STEPS (Continued)
AC004137AB
TOPSTACK
SIDE STAY
PAD
NO.1BOW
CONVERTIBLE TOP
TSB Revision
BODY
42-134
2. Guide the (folded) end of the topstack side stay pad out of
the wider slit of the No.1 bow.
3. Pull out the folded end of the topstack side stay, and
disconnect the topstack side stay pad from the No.1 bow.
4. Disconnect the topstack side stay pad from the No.2, No.3,
No.4, and No.5 bows.
INSTALLATION SERVICE POINT
.
>>A<< TOPSTACK SIDE STAY PAD ASSEMBLY INSTALLA-
TION
1. Face the folded end of the topstack side stay pad downward,
and then position it to the No.1 bow side.
2. Connect the topstack side stay pad to the No.5, No.4, No.3,
and No.2 bows.
3. Insert the folded end of the topstack side stay pad through
the wider part of the No.1 bow slit as shown.
4. Working from inside the vehicle, pull out the folded end of
the topstack side stay pad, and then install the topstack side
stay pad to the No.1 bow.
AC004138 AB
TOPSTACK
SIDE STAY
PAD
NO.1BOW
AC004139 AB
TOPSTACK
SIDE STAY
PAD
NO.1BOW
AC004140 AB
TOPSTACK
SIDE STAY
PAD
NO.1BOW SLIT
AC004138 AB
TOPSTACK
SIDE STAY
PAD
NO.1BOW
CONVERTIBLE TOP
TSB Revision
BODY
42-135
TOP COVER ASSEMBLY
REMOVAL AND INSTALLATION
M1426205100040
Post-installation Operation
• Convertible Top Fit Adjustment (Refer to
AC004142 AB
N
10
1
2
5
3
11
6
7
12
N
4
8
9
REMOVAL STEPS
• CONVERTIBLE TOP ASSEMBLY
1. TOP STACK PULL HANDLE BOX
BEZEL
2. NO.1 BOW GARNISH
<<A>> >>B<<
3. RIVET
4. TOP STACK REAR RAIL AND SIDE
CABLE ASSEMBLY CONNECTION
5. TOP COVER FROM NO.1 BOW
6. NO.2 BOW LISTING STRAP
7. NO.3 BOW LISTING STRAP
8. NO.4 BOW LISTING STRAP
9. REAR RAIL SAIL PANEL FLAP
10. TOP COVER FROM NO.5 BOW
>>A<<
11. SIDE CABLE ASSEMBLY
12. TOP COVER ASSEMBLY
REMOVAL STEPS (Continued)
CONVERTIBLE TOP
TSB Revision
BODY
42-136
REMOVAL SERVICE POINT
.
<<A>> RIVET REMOVAL
Use a drill [
φ4.0 − 4.5 mm (φ0.16 − 0.18 inch)] to break the rivet
by drilling a hole, and remove the rivet.
INSTALLATION SERVICE POINT
.
>>A<< SIDE CABLE ASSEMBLY INSTALLATION
1. Feed a wire through the hollow part at the side of the top
cover assembly.
2. Tie the rear end of the wire to the front end of the side cable
assembly, pull out the front end of the wire, and then feed
the side cable assembly through the hollow part.
3. Remove the wire.
.
>>B<< RIVET INSTALLATION
1. Insert the rivet [
φ4.8 mm (φ0.19 inch)] into the No.1 bow and
side cable tab.
2. Insert "A" of the rivet into the rivet tool.
3. Pressing the flange surface of the rivet, move the handle of
the rivet tool.
4. The thinnest point of "A" is cut and the rivet is held in the
position.
AC004141
NO.1 BOW
DRILL
RIVET
AB
AC004804 AB
SIDE CABLE
TAB
NO.1 BOW
A
RIVET
RIVET TOOL
FLANGE SURFACE
RIVET
TOP COVER ASSEMBLY
SIDE CABLE TAB
NO.1 BOW
RIVET TOOL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст