Mitsubishi Eclipse. Manual — part 983
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-9
GARNISHES AND MOLDINGS
REMOVAL AND INSTALLATION
M1511004400164
<ECLIPSE>
AC003619
ADHESIVE TAPE: DOUBLE-SIDED TAPE
[ 3 mm ( 0.1 in ) WIDTH AND 5 mm ( 0.2 in ) THICKNESS ]
VIEW A
5
1
SECTION A – A
1
1
5
SECTION B – B
SECTION C – C
SECTION D – D
A
A
B
B
C
C
D
D
5
4
2
1
VIEW A
CLIP
CLIP
CLIP
CLIP
AB
3
<<A>>
>>B<< 1. ROOF DRIP MOLDING
2. WINDSHIELD UPPER MOLDING
(REFER TO GROUP 42,
WINDSHIELD
3. BELT LINE MOLDING (REFER TO
GROUP 42
4. REAR WINDOW LOWER MOLDING
(REFER TO GROUP 42, LIFTGATE
GLASS
<<B>> >>A<<
5. REAR PILLAR GARNISH
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-10
Required Special Tools:
• MB990449: Window Molding Remover
• MB990784: Ornament Remover
<ECLIPSE SPYDER>
AC003620
1
2
3
4
5
AB
1. DRIP GARNISH
2. WINDSHIELD UPPER MOLDING
(REFER TO GROUP 42,
WINDSHIELD
3. BELT LINE MOLDING (REFER TO
GROUP 42, DOOR WINDOW
GLASS RUNCHANNEL AND DOOR
OPENING WEATHERSTRIP
4. BACK BELT MOLDING
5. QUARTER BELT SIDE GARNISH
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-11
REMOVAL SERVICE POINTS
.
<<A>> ROOF DRIP MOLDING REMOVAL
CAUTION
If the molding has become warped, it should not be
reused.
Use special tool MB990449 to lever out the molding.
.
<<B>> REAR PILLAR GARNISH REMOVAL
1. Use a resin spatula to scrape off the double-sided tape.
2. Wipe the body surface and clean it with a shop moistened
with isopropyl alcohol.
INSTALLATION SERVICE POINTS
.
>>A<< REAR PILLAR GARNISH INSTALLATION.
1. Scrape off the double-sided tape with a resin spatula or
gasket scraper.
2. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the protect molding surface.
CAUTION
Do not remove all of the residual adhesive.
3. Remove only a small portion of the residual adhesive.
CAUTION
• Always apply it evenly on the entire surface, because a
lot or little will reduce its strength.
• Do not touch the painted surface.
4. Affix the specified double-sided tape [3 mm (0.1 inch) wide
and 5 mm (0.2 inch) thick].
AC003626AB
MB990449
AC003627
DOUBLE-SIDE TAPE
AB
AC000422
AC003628
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-12
.
REAR PILLAR GARNISH INSTALLATION
1. Tear off the double-sided tape backing paper.
NOTE: If you attach the adhesive tape to the edge of the
backing paper, if will be easy to tear off.
2. Install the rear pillar garnish.
NOTE: If the double-sided tape is difficult to affix in cold
temperature, etc., warm the bonding surfaces of the body
and rear pillar garnish to about 40
−
60
°
C (104
−
140
°
F)
before affixing the tape.
3. Firmly press in the rear pillar garnish.
.
>>B<< ROOF DRIP MOLDING INSTALLATION
After installing the clip to the outer front pillar in alignment with
its section A, cut from section B.
AC000423 AB
ADHESIVE TAPE
BACKING PAPER
AC003629
FRONT PILLAR
OUTER
SECTION
B
SECTION A
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст