Mitsubishi Eclipse. Manual — part 220
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-373
STEP 8. Check the continuity at fuel tank temperature
sensor harness side connector D-17.
(1) Disconnect the connector D-17 and measure at the harness
side.
(2) Check for the continuity between terminal No. 1 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 9.
NO : Repair harness wire between fuel tank temperature
sensor connector D-17 (terminal No. 1) and ground
because of open circuit or harness damage. Then go
to Step 11.
AK300453
1
2
3
4
5
D-17 (GR)
AB
CONNECTOR: D-17
HARNESS CONNECTOR:
COMPONENT SIDE
AK101375
1
2
3
4
5
AH
1
2
3
4
5
D-17 HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-374
STEP 9. Check connector C-60 at ECM <M/T> or connector
C-54 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 11.
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
AK300412
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
C-54 (GR)
CONNECTOR: C-54 <A/T>
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-375
STEP 10. Check for open circuit and harness damage
between fuel tank temperature sensor connector D-17 and
ECM connector C-60 <M/T> or PCM connector C-54.
AK300453
1
2
3
4
5
D-17 (GR)
AB
CONNECTOR: D-17
HARNESS CONNECTOR:
COMPONENT SIDE
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
AK300412
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
C-54 (GR)
CONNECTOR: C-54 <A/T>
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-376
NOTE: Check harness after checking intermediate connector
C-90 and C-28. If intermediate connector are damaged, repair
or replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion
. Then go to Step 11.
Q: Is the harness wire in good condition?
YES : Replace the ECM or PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
STEP 11. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0183 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст