Mitsubishi Eclipse. Manual — part 987
DOOR MIRROR
TSB Revision
EXTERIOR
51-25
CAUTION
• Pressing the mark horizontally may lead to a slack,
clinching or improper position.
• If the mark is pressed improperly, the mark may be eas-
ily peeled off.
(3) Make sure that air bubbles are not trapped in the
application surface. When applying the mark, use special
tool MB990528 to press the mark from its center to top
and bottom gradually.
(4) Peel off an application tape (top protection paper)
horizontally and carefully from one end. If an air bubble is
left in the mark, open a hole by using a needle, and then
use special tool MB990528 to expel the air bubble.
DOOR MIRROR
SPECIAL TOOL
M1511000600586
AC000548 AB
30 - 45˚
MB990528
APPLICATION TAPE
AC000549
CORRECT INCORRECT
AB
APPLICATION TAPE
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784
Ornament remover
General service tool
Removal of remote
controlled mirror switch
MB990784
DOOR MIRROR
TSB Revision
EXTERIOR
51-26
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400342
AC003328
8
7
6
5
3
VIEW A
VIEW A
2
4
6
8
1
B
B
A
A
CLAW
SECTION A – A
6
2,3
2,3
6
SECTION B – B
VIEW A
2,3
(ELECTRIC)
(DIRECT)
AB
NOTE
: CLAW POSITION
1.
REMOTE CONTROLLED MIRROR
SWITCH
DOOR MIRROR REMOVAL STEPS
• DOOR TRIM (REFER TO GROUP
42
2. DELTA COVER, INNER
3. TWEETER COVER
4. PAD
5. TWEETER
6. DELTA COVER BASE
7. HARNESS CONNECTOR
<VEHICLES WITH REMOTE
CONTROLLED MIRROR>
8. DOOR MIRROR ASSEMBLY
DOOR MIRROR REMOVAL STEPS
DOOR MIRROR
TSB Revision
EXTERIOR
51-27
INSPECTION
M1511019100277
REMOTE CONTROLLED MIRROR ASSEMBLY
CHECK
1. Check that the mirror moves as described in the table when
each terminal is connected to the battery
2. Check if there is continuity between terminals 4 and 5.
<Vehicles with heated mirror>
REMOTE CONTROLLED MIRROR SWITCH
CONTINUITY CHECK
BATTERY CONNECTION
DIRECTION
OPERATION
• Connect terminal 3 to the negative
battery terminal
• Connect terminal 1 to the positive
battery terminal
Mirror glass should
face upward
• Connect terminal 1 to the negative
battery terminal.
• Connect terminal 3 to the positive
battery terminal.
Mirror glass should
face downward
• Connect terminal 2 to the negative
battery terminal.
• Connect terminal 3 to the positive
battery terminal.
Mirror glass should
face to the left
• Connect terminal 3 to the negative
battery terminal.
• Connect terminal 2 to the positive
battery terminal.
Mirror glass should
face to the right
AC003582
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Left side
Up
4
− 8, 6 − 7
Less than 2 ohms
Down
4
− 7, 6 − 8
Right
3
− 6, 4 − 7
Left
3
− 4, 6 − 7
Right side
Up
2
− 4, 6 − 7
Less than 2 ohms
Down
2
− 6, 4 − 7
Right
4
− 7, 6 − 9
Left
4
− 9, 6 − 7
5
4
6
3
2
1
9
8
7
AC001682
SPECIFICATIONS
TSB Revision
EXTERIOR
51-28
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1511015300280
SERVICE SPECIFICATIONS
M1511000300369
SEALANT AND ADHESIVE
M1511000500459
ITEM
SPECIFICATION
Front bumper
Front turn signal light screw
0.69
± 0.09 N⋅m (5.2 ± 0.8 in-lb)
Front fog light assembly screw
4.9
± 0.7 N⋅m (43 ± 6 in-lb)
Front fog light bracket bolt
4.9
± 0.7 N⋅m (43 ± 6 in-lb)
License plate garish screw
0.9
± 0.1 N⋅m (8 ± 1 in-lb)
Windshield wiper and washer
Wiper arm and blade assembly nut
13
± 3 N⋅m (113 ± 26 in-lb)
Wiper motor and wiper link assembly bolt 5.0
± 0.7 N⋅m (44 ± 6 in-lb)
Washer tank motor assembly bolt
12
± 1 N⋅m (100 ± 13 in-lb)
ITEM
STANDARD VALUE
Windshield wiper blade position installation
mm (in)
Driver's side
33
− 43 (1.3 − 1.7)
Passenger's side
38
− 48 (1.5 − 1.9)
Rear wiper blade position installation mm (in)
89
− 99 (3.5 − 3.9)
ITEM
SPECIFICATION
Rear pillar garnish
Adhesive tape: Double-sided tape [3 mm (0.1 in) width and
5 mm (0.2 in) thick]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст